External call . AGFEO AC 14 WebPhonie

Resetting the telecommunications system ¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢

You can return the programming of the telecommunications system to a defined condition by resetting. This may be necessary when unclear settings are to be reset or the telecommunications system is to be re-programmed.

After the reset, the telecommunications system operates again with the previously configured program. All the settings made by the programming mode or the PC program are retained providing the programming mode was terminated properly.

Attention! The following are deleted when the telecommunications system is reset:

- all existing internal and external connections

- remote configuration

- internal callbacks

- ISDN callback on busy

- Line reservations

Hardware reset – Pull the power pack from the socket of the 230 V mains and plug it back in.

Software reset – Run the following procedure

Software reset ¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢¢

Start programming mode: h

*PRO

(system PIN) q

ª

PRO

h * R E S ª

Lift handset

RES

et the telecommunications system

Replace handset

Rings

External call

Rhythm 0 (standard)

Rhythm 1

Rhythm 2

Rhythm 3

Rhythm 4

Internal call

Reserving a line

All ringing rhythms for incoming external calls start with an initial ringing of 500 ms. This is followed by a 2 s pause. This is for technical reasons to transmit the caller’s phone number (CLIP). It is then possible to distinguish calls under different phone numbers of the telecommunications system (see diagram).

{{{{{{{{{{||||||||||||||||||||||||||||||||||||||{{{{{{{{{{||||||||||||||||||||||||||||||

An external subscriber calls

{{{{{{{{||{{||||||||||||||||||||||||||||||||||||{{{{{{{{||{{||||||||||||||||||||||||||||

. . .

. . .

{{{{{{{{||{{||{{||||||||||||||||||||||||||||||||{{{{{{{{||{{||{{||||||||||||||||||||||||

. . .

{{{{{{{{||{{||{{||{{||||||||||||||||||||||||||||{{{{{{{{||{{||{{||{{||||||||||||||||||||

. . .

{{{{{{{{||{{||{{||{{||{{||||||||||||||||||||||||{{{{{{{{||{{||{{||{{||{{||||||||||||||||

. . .

{{{{||||||||||||||||||{{{{||||||||||||||||||{{{{||||||||||||||||||{{{{||||||||||||||||||

. . .

An internal subscriber calls

{{{{||||{{{{||||{{{{||||{{{{||||{{{{

Explanation:

{{{{{{{{{{||||||||||

. . .

Ring pause continued

The rings may deviate depending on the terminal used.

A - 4 Appendix

Tones

Dialling tone

- internal

- external

{{||{{||{{||||||||||||{{||{{||{{||||||||||||{{||{{||{{||||||||||||{{||{{||{{|||||||||||| signals that you can dial after lifting the handset

. .

.

{{{{{{{{{{{{{{{{{{{{{{{{{{{{{{{{{{{{{{{{{{{{{{{{{{{{{{{{{{{{{{{{{{{{{{{{{{{{{{{{{{{{{{{{

.

. .

.

continuous tone which you hear when you have seized a line after dialling “0”

Ringing tone

- internal

- external

Busy tone

Special dialling tones

- Programming tone

- Lock tone

{{{{||||||||||||||||||{{{{||||||||||||||||||{{{{||||||||||||||||||{{{{||||||||||||||||||

The internal subscriber is called

. . .

{{{{||||||||||||||||{{{{||||||||||||||||{{{{||||||||||||||||{{{{||||||||||||||||{{{{||||

The external subscriber is called

. . .

{{||||{{||||{{||||{{||||{{||||{{||||{{||||{{||||{{||||{{||||{{||||{{||||{{||||{{||||{{||

The dialled internal or external subscriber is busy

. . .

||{}||{}||{}{{}{}{}{}{||||{}||{}||{}{{}{}{}{}{||||{}||{}||{}{{}{}{}{}{||||{}||{}||{}{{}{

. . .

Signals, after lifting the handset, that you can dial but do not disturb, automatic dialling or a diversion is switched on

{{|||||||||||||||{{|||||||||||||||{{|||||||||||||||{{|||||||||||||||{{|||||||||||||||

. .

.

Signals, after lifting the handset, that you cannot dial, the programming mode or the cost menu are switched on

{{|{{||||||||||||||||||||||||||||{{|{{||||||||||||||||||||||||||||{{|{{|||||||||||||||

Signals, after lifting the handset, that the telephone is locked.

. .

.

Knocking tone

- internal

- external

Acknowledgement tone

{{{{

Signals an internal call in your conversation

{{||||{{||||||||||||||||||||||||||||||||||||||||||||||||||||||{{||||{{|

. . .

Signals an external call in your conversation after 10 s

{{{{

Input accepted

A

Error tone

{{||||{{||||{{||||{{||||{{||||{{||||{{||||{{||||{{||||{{||||{{||||{{||||{{||||{{||||{{||

Operating error/input rejected

. . .

Explanation:

{{{{{{{{{{||||||||||

. . .

tone pause continued

Appendix A - 5

Technical data

Housing dimensions

Weight

Ambient temperature

- operation/storage

Humidity

Main connection

- power consumption at

U rated

= 230 V and full load

- length of the connecting cable

- power pack (type)

S0 access

- connection

- length IAE cable

15.4 x 21.5 x 4.6 (width x height x depth) in cm

980 g including power pack

5 °C to 40 °C/-25 °C to +70 °C max. 70% (no condensation)

230 VAC, +10%/-10%, 50 Hz

I rated

2 m

= 40 mA (9 VA)

TST 433238

Multi-equipment access, Euro ISDN by Western socket RJ45 and enclosed

IAE connecting cable IAE8/IAE8

1.5 m

Analog terminals

- range

- connection

- dialling method

- refer back key

- Modem operation

4 a/b terminals (telephone, answering machine, fax, modem

2 x 50 ohms (ø 0.6 mm, 800 m) symmetrical, 2-wire via TASE connections without coding F or N or via screw terminals, plug-in

Pulse dialling or DTMF

Flash (50 to 200 ms) transmission speed up to 56600bps, can be reduced if necessary to 33600 bps by transmission path and lines

PC interface

- range

- connection

USB interface

- length of the USB cable similar to RS 232C

3 m, +/-5 V

9-pole D-Sub socket

Universal Serial Bus

3 m

Data backup during power failure unlimited

Music on Hold (MoH) internal, 1 melodie

A - 6 Appendix