124 Commissioning

Pos: 93 /Alle Serie n (Allge mein e M odul e)/Üb ersc hrift en/Ebe ne 1/In Be trie b ne hme n - Ü ber schrif t 1 @ 4\ mod _124 090 145 275 0_2 1.doc x @ 3 157 0 @ 1 @ 1

8 Commissioning

WAGO I/O System 750

750-890 Controller Modbus TCP; G4; 2ETH; SD

Pos: 94. 1 /Seri e 75 0 (WAGO I/O SYSTEM )/I n Betri eb n ehm en/ Feld buskn ote n in Bet rieb neh me n/In Be trie b ne hme n Einleit ung - Anfa ng (Koppl er/Co ntr oller ) @ 4 \mo d_1 238 483 034 921_ 21. docx @ 29 371 @ @ 1 This section shows a step-by-step procedure for starting up exemplarily a WAGO fieldbus node.

Pos: 94. 2 /Seri e 75 0 (WAGO I/O SYSTEM )/I n Betri eb n ehm en/ Feld buskn ote n in Bet rieb neh me n/Einleitu ng - Hinweis: Exem plarisc hes Beis piel, n ur 4 er for derlic he Ar beitssch ritte (8 9x) Ko ppl/Co ntr @ 34 \mo d_1 550 048 0663 86_ 21. docx @ 52 9279 @ @ 1

Good example!

This description is just an example and only serves to describe the procedure for a local start-up of a single fieldbus node with a PC under Windows.

In principle, only a few steps are required for start-up.

To enable communication from your PC to the fieldbus coupler/controller over network, both must be in the same network. This requires that you first determine the IP address of the PC and then assign a corresponding IP address to the fieldbus node. There are several options being available for IP address assignment.

The description of these single work steps can be found in the corresponding following chapters.

•

•

•

•

Connecting PC and fieldbus node

Determing IP address of the PC

Assigning IP address to the fieldbus node

Applying IP address permanently (option “static”)

Pos: 94. 3 /Seri e 75 0 (WAGO I/O SYSTEM )/I n Betri eb n ehm en/ Feld buskn ote n in Bet rieb neh me n/Einleitu ng - Anfa ng - im Ansc hluss si nd zu sätzlich e T he men besch rieb en: Flash , Uh r, Def aul o hne R TC @ 34\ mod _15 507 625 962 22_ 21.d ocx @ 532 593 @ @ 1 Following the commissioning descriptions after which the fieldbus node is ready for communication, the following topics are described:

•

•

•

Preparing the Flash File System

Synchronizing the System Time

Restoring Factory Settings

Pos: 94. 4 /Seri e 75 0 (WAGO I/O SYSTEM )/I n Betri eb n ehm en/ Feld buskn ote n in Bet rieb neh me n/Einleitu ng - Ende (Kop fstatio n) - Pro gra mmi eru ng @ 34\ mod _15 507 642 9944 4_2 1.d ocx @ 532 621 @ @ 1 After the topics specified above, you can find instructions for programming the head station with WAGO-I/OPRO and the description of the internal HTML pages of the web-based Management System (WBM) for additional settings of the head station.

Pos: 94. 5 /Dok ume ntati on all gem ein/Glie de rung sele ment e/- --Seit enwec hsel- -- @ 3\ mod_ 122 110 804 507 8_0. docx @ 21 810 @ @ 1

Manual

Version 1.2.2