- Computers & electronics
- Computer components
- Interface components
- Digital & analog I/O modules
- ADLINK Technology
- PCI-8136M
- User's Guide
advertisement
![Voltage output signals DAC. ADLINK Technology PCI-8136M | Manualzz Voltage output signals DAC. ADLINK Technology PCI-8136M | Manualzz](http://s1.manualzz.com/store/data/001438114_1-e075bc2fb8e61a7cd0411c36ed8396e4-360x466.png)
3.2 Voltage output signals DAC
There are 6 DAC output channels on PCI-8136M. If the closed loop control mode is set for any one of the 6 axes, its corresponding DAC channel will be treated as voltage command output. If not, the DAC channel will be treated as a general purposed analog output channel.
The resolution of DAC is 16-bit, and the output voltage ranged from -10 V to
+10V. To make correct connection, please refer to following figure:
Figure 3.2.1 DAC circuit
The Analog outputs are all single ended with common ground ‘AGND’. The following table is the pin assignment information for DAC.
CN1 Pin No
2
3
4
52
53
54
1
51
Signal Name
DAC1
DAC2
DAC3
DAC4
DAC5
DAC6
AGND
AGND
Description
DAC Channel 1
DAC Channel 2
DAC Channel 3
DAC Channel 4
DAC Channel 5
DAC Channel 6
Analog Ground
Analog Ground
CN3 Pin No
18
19
6
5
13
Signal Name
DAC1
DAC2
DAC3
AGND
AGND
Description
DAC Channel 1
DAC Channel 2
DAC Channel 3
Analog Ground
Analog Ground
20
• Signal Connection
Notice that the DAC Channel 1~ 3 in CN1 and CN3 are connected inside the
PCI-8136M.
Signal Connection
• 21
advertisement
Related manuals
advertisement
Table of contents
- 11 Functionality of PCI-8136M
- 12 Features
- 13 Specifications
- 13 Applicable Motors
- 13 Motion
- 13 Motion Interface I/O Signals
- 14 General I/Os
- 15 General Specifications
- 16 Software Supporting
- 16 Programming Library
- 18 What You Have
- 19 Outline Drawing
- 20 Hardware Installation
- 20 Hardware configuration
- 20 PCI slot selection
- 20 Installation Procedures
- 20 Trouble shooting
- 21 Software Installation
- 22 CN1 PIN ASSIGNMENTS: MAIN CONNECTOR
- 23 CN2 PIN ASSIGNMENTS: EXTERNAL POWER INPUT
- 24 CN3 PIN ASSIGNMENTS: DB25 CONNECTOR
- 24 CN4 PIN ASSIGNMENTS: DB9 CONNECTOR
- 26 Pulse output signals OUT and DIR
- 28 Voltage output signals DAC
- 30 Encoder feedback signals EA, EB and EZ
- 33 Analog Input
- 35 Origin signal ORG
- 36 End-Limit signals PEL and MEL
- 37 Emergency stop signal ESTOP
- 38 Servo on signal SVON
- 39 General purpose output P-RDY
- 39 VCC Pin
- 40 Open Loop and Closed Loop Connection
- 43 AD Conversion and Preloaded Trigger
- 43 Voltage Compare
- 44 DA Conversion
- 44 DA Output by Trigger Source
- 45 Local DIO
- 45 Digital Input
- 45 Digital Output
- 46 Pulse Input and Position Compare
- 46 Pulse Input
- 47 Position Counter Value Capture (Latch)
- 48 Position Compare
- 49 Pulse Output
- 51 Remote Serial IO
- 52 Introduction to DDA
- 53 Open-loop and close-loop control
- 53 Open-loop control
- 53 Close-loop control
- 54 Constant Velocity Motion
- 55 Trapezoidal Motion
- 57 S-Curve Profile Motion
- 59 2D Interpolation
- 62 3D Interpolation
- 63 Home Return Mode
- 64 Motion Parameters Setting
- 65 The Motion IO Interface
- 65 SERVO ON
- 65 Limit Switch Signal
- 65 Emergency stop signal (ESTOP)
- 67 Interrupt Control
- 71 List of Functions
- 73 Initialization
- 75 System Parameters
- 77 Card Information
- 78 Digital I/O
- 80 Remote I/O
- 82 Analog I/O
- 85 Pulse I/O
- 89 Interrupt Control
- 92 Close Loop Initialization
- 93 Motion Parameters
- 96 Motion Status
- 98 PTP Movement
- 100 2D Interpolation
- 102 3D Interpolation
- 104 Continuous Motion
- 105 Homing
- 106 Motion Function