- Computers & electronics
- Computer components
- Interface components
- Digital & analog I/O modules
- ADLINK Technology
- PCI-8136M
- User's Guide
advertisement
![DA Conversion. ADLINK Technology PCI-8136M | Manualzz DA Conversion. ADLINK Technology PCI-8136M | Manualzz](http://s1.manualzz.com/store/data/001438114_1-e075bc2fb8e61a7cd0411c36ed8396e4-360x466.png)
Relative functions:
_8136_A_Set_Compare_Value(), _8136_A_Set_Compare_Volt (),
_8136_S_Set_Int_Factor() : please refer to section 5,9
4.2 DA Conversion
The PCI-8136M provides 6 channel 16-bit, bipolar (±10V DC) digital to analog converter. The D (value assigned) to A (voltage output) converting table is showed bellow.
4.2.1 DA Output by Trigger Source
PCI-8136 allows users to set a pre-load value for each DAC channel. The value will be sent once any trigger condition for this channel is happened.
The trigger source could be from encoder counter comparators or ADCs by setting the trigger map in the software functions. Users can set every channel's trigger sources independently. The compare method could be set in Set_Int_Factor() function.
Related functions:
_8136_A_Initial() : please refer to section 5.2
_8136_A_Write_Value(), _8136_A_Write_Volt(),
_8136_A_Output_Control() : please refer to section 5.7
_8136_A_Set_Preload_Volt(), _8136_A_Set_Trigger(),
_8136_A_Set_Trigger_Map() : please refer to section 5.7
_8136_S_Set_Int_Factor() : please refer to section 5,9
36
• Operation Theorem
advertisement
Related manuals
advertisement
Table of contents
- 11 Functionality of PCI-8136M
- 12 Features
- 13 Specifications
- 13 Applicable Motors
- 13 Motion
- 13 Motion Interface I/O Signals
- 14 General I/Os
- 15 General Specifications
- 16 Software Supporting
- 16 Programming Library
- 18 What You Have
- 19 Outline Drawing
- 20 Hardware Installation
- 20 Hardware configuration
- 20 PCI slot selection
- 20 Installation Procedures
- 20 Trouble shooting
- 21 Software Installation
- 22 CN1 PIN ASSIGNMENTS: MAIN CONNECTOR
- 23 CN2 PIN ASSIGNMENTS: EXTERNAL POWER INPUT
- 24 CN3 PIN ASSIGNMENTS: DB25 CONNECTOR
- 24 CN4 PIN ASSIGNMENTS: DB9 CONNECTOR
- 26 Pulse output signals OUT and DIR
- 28 Voltage output signals DAC
- 30 Encoder feedback signals EA, EB and EZ
- 33 Analog Input
- 35 Origin signal ORG
- 36 End-Limit signals PEL and MEL
- 37 Emergency stop signal ESTOP
- 38 Servo on signal SVON
- 39 General purpose output P-RDY
- 39 VCC Pin
- 40 Open Loop and Closed Loop Connection
- 43 AD Conversion and Preloaded Trigger
- 43 Voltage Compare
- 44 DA Conversion
- 44 DA Output by Trigger Source
- 45 Local DIO
- 45 Digital Input
- 45 Digital Output
- 46 Pulse Input and Position Compare
- 46 Pulse Input
- 47 Position Counter Value Capture (Latch)
- 48 Position Compare
- 49 Pulse Output
- 51 Remote Serial IO
- 52 Introduction to DDA
- 53 Open-loop and close-loop control
- 53 Open-loop control
- 53 Close-loop control
- 54 Constant Velocity Motion
- 55 Trapezoidal Motion
- 57 S-Curve Profile Motion
- 59 2D Interpolation
- 62 3D Interpolation
- 63 Home Return Mode
- 64 Motion Parameters Setting
- 65 The Motion IO Interface
- 65 SERVO ON
- 65 Limit Switch Signal
- 65 Emergency stop signal (ESTOP)
- 67 Interrupt Control
- 71 List of Functions
- 73 Initialization
- 75 System Parameters
- 77 Card Information
- 78 Digital I/O
- 80 Remote I/O
- 82 Analog I/O
- 85 Pulse I/O
- 89 Interrupt Control
- 92 Close Loop Initialization
- 93 Motion Parameters
- 96 Motion Status
- 98 PTP Movement
- 100 2D Interpolation
- 102 3D Interpolation
- 104 Continuous Motion
- 105 Homing
- 106 Motion Function