- Computers & electronics
- Computer components
- Interface components
- Digital & analog I/O modules
- ADLINK Technology
- PCI-8136M
- User's Guide
advertisement
4.14 Home Return Mode
In most applications, home point is a very important reference to the coordinate of space. The PCI-8136M has a simple way to search a home point which is connected to the ORG pin of CN1. After giving a home moving command, the axis will start to move toward one direction until the ORG signal is reached. Once the ORG is triggered, the axis will stop immediately and clear the encoder counter.
The example of homing function is as follows:
_8136_Home_Move(CardNo, AxisNo, Str_V, Max_V, Tacc)
The Str_V and Max_V's value decide the searching direction of homing.
Relative Functions:
_8136_P_Initial() refer to section 5.2
_8136_Motion_Stop() refer to section 5.18
_8136_Home_Move() refer to section 5.17
Operation Theorem
• 55
advertisement
Related manuals
advertisement
Table of contents
- 11 Functionality of PCI-8136M
- 12 Features
- 13 Specifications
- 13 Applicable Motors
- 13 Motion
- 13 Motion Interface I/O Signals
- 14 General I/Os
- 15 General Specifications
- 16 Software Supporting
- 16 Programming Library
- 18 What You Have
- 19 Outline Drawing
- 20 Hardware Installation
- 20 Hardware configuration
- 20 PCI slot selection
- 20 Installation Procedures
- 20 Trouble shooting
- 21 Software Installation
- 22 CN1 PIN ASSIGNMENTS: MAIN CONNECTOR
- 23 CN2 PIN ASSIGNMENTS: EXTERNAL POWER INPUT
- 24 CN3 PIN ASSIGNMENTS: DB25 CONNECTOR
- 24 CN4 PIN ASSIGNMENTS: DB9 CONNECTOR
- 26 Pulse output signals OUT and DIR
- 28 Voltage output signals DAC
- 30 Encoder feedback signals EA, EB and EZ
- 33 Analog Input
- 35 Origin signal ORG
- 36 End-Limit signals PEL and MEL
- 37 Emergency stop signal ESTOP
- 38 Servo on signal SVON
- 39 General purpose output P-RDY
- 39 VCC Pin
- 40 Open Loop and Closed Loop Connection
- 43 AD Conversion and Preloaded Trigger
- 43 Voltage Compare
- 44 DA Conversion
- 44 DA Output by Trigger Source
- 45 Local DIO
- 45 Digital Input
- 45 Digital Output
- 46 Pulse Input and Position Compare
- 46 Pulse Input
- 47 Position Counter Value Capture (Latch)
- 48 Position Compare
- 49 Pulse Output
- 51 Remote Serial IO
- 52 Introduction to DDA
- 53 Open-loop and close-loop control
- 53 Open-loop control
- 53 Close-loop control
- 54 Constant Velocity Motion
- 55 Trapezoidal Motion
- 57 S-Curve Profile Motion
- 59 2D Interpolation
- 62 3D Interpolation
- 63 Home Return Mode
- 64 Motion Parameters Setting
- 65 The Motion IO Interface
- 65 SERVO ON
- 65 Limit Switch Signal
- 65 Emergency stop signal (ESTOP)
- 67 Interrupt Control
- 71 List of Functions
- 73 Initialization
- 75 System Parameters
- 77 Card Information
- 78 Digital I/O
- 80 Remote I/O
- 82 Analog I/O
- 85 Pulse I/O
- 89 Interrupt Control
- 92 Close Loop Initialization
- 93 Motion Parameters
- 96 Motion Status
- 98 PTP Movement
- 100 2D Interpolation
- 102 3D Interpolation
- 104 Continuous Motion
- 105 Homing
- 106 Motion Function