14.6. Zone Attributes. Eldes EKB3

Config

Tool

This operation may be carried out from the PC using the ELDES Configuration Tool software.

NOTE: The system will NOT activate siren/bell and keypad buzzer only when Panic/Silent zone type is violated.

14.6. Zone Attributes

• Stay – If this attribute is enabled, the zone, regardless of type, will not cause an alarm if violated when the system is Stay armed. For more details on arming the system in the Stay mode, please refer to 15. STAY MODE.

• Force – This attribute determines whether the system can be armed or not while a zone is violated. If a zone with the Force attribute enabled is left violated until the exit delay expires, it will be ignored. Once the system is armed and the zone is restored, the violation will not be ignored and the zone will operate according to the determined type. For more details on zone types, please refer to 14.5.

Zone Type Definitions.

• Delay, ms – This attribute determines the zone sensitivity level by delay time (By default – 800 milliseconds). If a zone is left triggered until the delay time expires, the zone is considered violated.

• Delay becomes Instant in Stay mode – This attribute determines whether or not any Delay type zone will operate as Instant type zone when the system is armed in the Stay mode. When the system is fully armed, the Delay type zone will operate normally. For more details on Delay and Instant zone types, please refer to 14.5. Zone Type Definitions.

• Chime – This feature is used to emit 3 short beeps from the keypad buzzer and display icon on EKB2 keypad screen whenever any

Delay type zone is violated. Typically, the feature is used for designated exit/entry doors to indicate the opening of the doors.

• Alarm count to bypass – This attribute determines a number of times the zone can be violated until it is automatically bypassed.

For more details on zone bypassing and how to activate a bypassed zone, please refer to 14.7. Bypassing and Activating Zones.

Enable Stay attribute for individual zone

EKB2

EKB3

Menu path:

On-board zone: OK → CONFIGURATION → OK → aaaa → OK → ZONES → OK → ONBOARD

ZONES → OK → ZONE 1... 12 → OK → STAY → OK → ENABLE → OK

Wireless zone: OK → CONFIGURATION → OK → aaaa → OK → ZONES → OK → WIRELESS

ZONES → OK → WLESS ZONE 1... 16 → OK → STAY → OK → ENABLE → OK

Keypad zone: OK → CONFIGURATION → OK → aaaa → OK → ZONES → OK → KEYPAD

ZONES → OK → KEYPAD 1... 4 ZONE → OK → STAY → OK → ENABLE → OK

EPGM1 zone: OK → CONFIGURATION → OK → aaaa → OK → ZONES → OK → EPGM1 ZONES →

OK → EPGM1 ZONE 1... 16 → OK → STAY → OK → ENABLE → OK

Value: aaaa – 4-digit administrator password.

Enter parameter 56, zone number & parameter status value:

56 nn 1 #

Value: nn – zone number, range – [01... 44].

Example: 56041#

MANUAL ELDES ESIM264 V3.1

EN

Config

Tool

This operation may be carried out from the PC using the ELDES Configuration Tool software.

Disable Stay attribute for individual zone

EKB2

EKB3

Menu path:

On-board zone: OK → CONFIGURATION → OK → aaaa → OK → ZONES → OK → ONBOARD

ZONES → OK → ZONE 1... 12 → OK → STAY → OK → DISABLE → OK

Wireless zone: OK → CONFIGURATION → OK → aaaa → OK → ZONES → OK → WIRELESS

ZONES → OK → WLESS ZONE 1... 16 → OK → STAY → OK → DISABLE → OK

Keypad zone: OK → CONFIGURATION → OK → aaaa → OK → ZONES → OK → KEYPAD

ZONES → OK → KEYPAD 1... 4 ZONE → OK → STAY → OK → DISABLE → OK

EPGM1 zone: OK → CONFIGURATION → OK → aaaa → OK → ZONES → OK → EPGM1

ZONES → OK → EPGM1 ZONE 1... 16 → OK → STAY → OK → DISABLE → OK

Value: aaaa – 4-digit administrator password.

Enter parameter 56, zone number & parameter status value:

56 nn 0 #

Value: nn – zone number, range – [01... 44].

Example: 56190#

Config

Tool

This operation may be carried out from the PC using the ELDES Configuration Tool software.

Enable Force attribute for individual zone

EKB2

EKB3

Menu path:

On-board zone: OK → CONFIGURATION → OK → aaaa → OK → ZONES → OK → ONBOARD

ZONES → OK → ZONE 1... 12 → OK → FORCE → OK → ENABLE → OK

Wireless zone: OK → CONFIGURATION → OK → aaaa → OK → ZONES → OK → WIRELESS

ZONES → OK → WLESS ZONE 1... 16 → OK → FORCE → OK → ENABLE → OK

Keypad zone: OK → CONFIGURATION → OK → aaaa → OK → ZONES → OK → KEYPAD ZONES

→ OK → KEYPAD 1... 4 ZONE → OK → FORCE → OK → ENABLE → OK

EPGM1 zone: OK → CONFIGURATION → OK → aaaa → OK → ZONES → OK → EPGM1 ZONES →

OK → EPGM1 ZONE 1... 16 → OK → FORCE → OK → ENABLE → OK

Value: aaaa – 4-digit administrator password.

Enter parameter 82, zone number & parameter status value:

82 nn 1 #

Value: nn – zone number, range – [01... 44].

Example: 82061#

Config

Tool

This operation may be carried out from the PC using the ELDES Configuration Tool software.

Disable Force attribute for individual zone

EKB2

EKB3

Menu path:

On-board zone: OK → CONFIGURATION → OK → aaaa → OK → ZONES → OK → ONBOARD

ZONES → OK → ZONE 1... 12 → OK → FORCE → OK → DISABLE → OK

Wireless zone: OK → CONFIGURATION → OK → aaaa → OK → ZONES → OK → WIRELESS

ZONES → OK → WLESS ZONE 1... 16 → OK → FORCE → OK → DISABLE → OK

Keypad zone: OK → CONFIGURATION → OK → aaaa → OK → ZONES → OK → KEYPAD

ZONES → OK → KEYPAD 1... 4 ZONE → OK → FORCE → OK → DISABLE → OK

EPGM1 zone: OK → CONFIGURATION → OK → aaaa → OK → ZONES → OK → EPGM1 ZONES→

OK → EPGM1 ZONE 1... 16 → OK → STAY → OK → DISABLE → OK

Value: aaaa – 4-digit administrator password.

Enter parameter 82, zone number & parameter status value:

82 nn 0 #

Value: nn – zone number, range – [01... 44].

Example: 82110#

52 EN MANUAL ELDES ESIM264 V3.1

Config

Tool

This operation may be carried out from the PC using the ELDES Configuration Tool software.

Set Delay, ms atrribute

Config

Tool

This operation may be carried out from the PC using the ELDES Configuration Tool software.

Enable/disable Delay becomes Instant in

Stay mode attribute

Config

Tool

This operation may be carried out from the PC using the ELDES Configuration Tool software.

Disable Chime attribute

EKB2

Menu path:

OK → CONFIGURATION → OK →aaaa → OK → ZONES → OK → CHIME → OK → DISABLE → OK

Value: aaaa – 4-digit administrator password.

EKB3

Enter parameter 32 & parameter status value:

32 0 #

Example: 320#

Config

Tool

This operation may be carried out from the PC using the ELDES Configuration Tool software.

Enable Chime attribute

EKB2

Menu path:

OK → CONFIGURATION → OK → aaaa → OK → ZONES → OK → CHIME → OK → ENABLE → OK

Value: aaaa – 4-digit administrator password.

EKB3

Enter parameter 32 & parameter status value:

32 1 #

Example: 321#

Config

Tool

This operation may be carried out from the PC using the ELDES Configuration Tool software.

Set Alarm count to bypass attribute for individual zone

Config

Tool This operation may be carried out from the PC using the ELDES Configuration Tool software.

MANUAL ELDES ESIM264 V3.1

EN