32.7. EWS2 – Wireless Outdoor Siren. Eldes EKB3

ATTENTION: The minimum wireless connection range between the wireless device and wireless antenna of ESIM264 system can be

0,5 meters.

32.6.3. EWS1 Zone, PGM Output & Tamper

Upon successful EWS1 indoor siren binding process,the system adds 1 wireless Instant zone and 1 wireless Siren PGM output. The wireless zone is intended for EWS1 tamper control and the wireless PGM output is for siren control.

In case of tamper violation, the alarm is caused regardless of system being armed or disarmed. The wireless connection loss between EWS1 and ESIM264 system leads to alarm. The system identifies this event as a tamper violation and sends alarm by SMS text message and phone call to the user (-s) by default. The SMS text message contains the violated tamper number and a star * character indicating wireless connection loss as a tamper alarm cause.

ATTENTION: The tamper will not operate if the wireless zone is disabled.

32.6.4. Battery Replacement

1. Open EWS1 enclosure.

2. Remove all 3 old batteries from the battery slots.

3. Postition the 3 new 1,5V alkaline AA type batteries according to the appropriate battery slot positive/negative terminals indicated on the

PCB (printed-circuit-board) of EWS1

4. Insert the batteries into the battery slots.

5. Batteries replaced.

For more details, please refer to 32.6.2 Installation.

ATTENTION: Only CR2032 3V batteries can be used. Install only new, high quality and unexpired batteries. Do not mix the old batteries with the new ones.

ATTENTION: At least 1 battery must be removed if the device is not in use.

ATTENTION: In order to avoid fire or explosion hazards, the system must be used only with approved battery. Special care must be taken when connecting positive and negative battery terminals. Dispose old batteries only into special collection sites. Do not charge, disassemble, heat or incinerate old batteries.

NOTE: The battery status can be monitored in real-time using ELDES Configuration Tool software.

32.6.5. Restoring Default Parameters

1. Remove any battery from EWS1.

2. Press and hold the RESET button.

3. Insert the battery back to EWS1.

4. Hold the RESET button until LED indicator provides several short flashes.

5. Release the RESET button.

6. Parameters restored to default.

32.7. EWS2 – Wireless Outdoor Siren

Main EWS2 features:

• Audio alarm indication by built-in speaker;

• Visual alarm indication by built-in LED indicators;

• Range of operating temperature: -30...+55 o C.

EWS2 is a wireless outdoor device with a built-in siren speaker, LED indicators and operates with ELDES wireless alarm systems. EWS2 has to be bind to the alarm system by sending a corresponding SMS text message or using software ELDES Configuration Tool. Upon successful EWS2 binding process, the system adds one wireless zone and one wireless PGM output. In case of alarm, the siren provides a sound alarm for one minute. The configuration of this parameter is disabled for EWS2 in order to save the battery power.

It is possible to connect up to 16 EWS2 devices to the alarm system at a time. The maximum wireless connection range is 150 meters (in open areas).

MANUAL ELDES ESIM264 V3.1

EN

32.7.1. Technical Specifications

32.7.1.1. Electrical & Mechanical Characteristics

Battery Type

Number of Batteries

1,5V Alkaline AA type

4

Battery Operation Time ~18 months*

Wireless Transmitter-Receiver Frequency 868 Mhz

Range of Operating Temperatures

Dimensions

Humidity

-30...+55ºC

201 x 140 x 36 mm

0-90% RH @ 0... +40 °C (non-condensing)

Wireless Communication Range

Compatible with Alarm Systems

Acoustic sound level

Up to 30 meters in premises; up to

150 meters in open areas

ELDES Wireless

~104 dB measured at 1 m

* The operation time depends on different conditions and may vary.

74

+ BATTERY +

TAMPER + -

BELL

BATTERY -

BATTERY + BATTERY +

32.7.1.2. Main Unit, LED & Connector Functionality

RESET

+ / -

LED indicators

Tamper

Bell+

Bell-

Button for restoring default parameters

Battery slots

Visual alarm indication

Tamper button terminals

Positive siren speaker terminal

Negative siren speaker terminal

32.7.2. Installation

1. Open EWS2 enclosure.

75 76

RESET

Remove the small blue lid located on the front side of the enclosure by pulling the lid up. (see Fig. No. 75).

Unscrew the front side of the enclosure (see Fig. No. 76).

2. Once the enclosure is opened, remove the plastic tab inserted between one of the battery terminal and battery slot contact (see Fig. No. 77).

77

3. Fix the siren on the wall using the screws (see Fig. No. 78).

MANUAL ELDES ESIM264 V3.1

78

+ BATTERY + BATTERY -

BATTERY + BATTERY +

4. Close EWS2 enclosure (see Fig. No. 76, Fig. No. 75)

5. Bind the device to the alarm system by sending a corresponding command via SMS text message or using ELDES Configuration Tool software. Please, refer to the software‘s HELP section or refer to 19.1. Binding, Removing and Replacing Wireless Devices for more details.

6. The system automatically informs about successful/unsuccessful binding process. If attempt to bind is unsuccessful, try to move EWS2 closer to alarm system device and bind it again.

7. EWS2 siren is ready for use.

NOTE: If you are unable to bind the wireless device please , restore the parameters of the wireless device to default and try again. See

32.7.6. Restoring Default Parameters for more details.

ATTENTION: The minimum wireless connection range between the wireless device and wireless antenna of ESIM264 system can be

0,5 meters.

32.7.3. EWS2 Zone, PGM Output & Tamper

Upon successful EWS2 outdoor siren binding process,the system adds 1 wireless Instant zone and 1 wireless Siren PGM output. The wireless zone is intended for EWS2 tamper control and the wireless PGM output is for siren control.

In case of tamper violation, the alarm is caused regardless of system being armed or disarmed. There are 2 ways to detect tamper violation on EWS2:

• By tamper button. EWS2 has a built-in tamper button intended for monitoring the enclosure status. Once the enclosure of EWS2 is illegally opened, the tamper button becomes unpressed. This action is followed by alarm which is sent by SMS text message and phone call to the user (-s) by default. The SMS text message contains the violated tamper number.

• By wireless connection loss. The wireless connection loss between EWS2 and ESIM264 alarm system leads to alarm. The sys tem identifies this event as a tamper violation and sends alarm by SMS text message and phone call to the user (-s) by default. The SMS text message contains the violated tamper number and a star * character indicating wireless connection loss as a tamper alarm cause.

ATTENTION: The tamper will not operate if the wireless zone is disabled.

32.7.4. Battery Replacement

1. Open EWS2 enclosure.

2. Remove all 4 old batteries from the battery slots.

3. Postition the 4 new 1,5V alkaline AA type batteries according to the appropriate battery slot positive/negative terminals indicated on the

PCB (printed-circuit-board) of EWS2

4. Insert the batteries into the battery slots.

5. Batteries replaced.

For more details, please refer to 32.7.2 Installation.

ATTENTION: Only 1,5V Alkaline AA type batteries can be used. Install only new, high quality and unexpired batteries. Do not mix the old batteries with the new ones.

MANUAL ELDES ESIM264 V3.1

EN