![](http://s1.manualzz.com/store/data/014871686_1-1841fd096382c1a4c1b47c8ed8c9056f-128x128.png)
advertisement
![PAR 1 RGBW User Manual Professional Entertainment Technology | Manualzz PAR 1 RGBW User Manual Professional Entertainment Technology | Manualzz](http://s1.manualzz.com/store/data/014871686_1-1841fd096382c1a4c1b47c8ed8c9056f-360x466.png)
Use gentle pressure only when cleaning, and work in a clean, well-lit area. Do not use any product that contains solvents or abrasives, as these can cause surface damage.
To clean the fixture:
1. Disconnect the fixture from power and allow it to cool for at least 10 minutes.
2. Vacuum or gently blow away dust and loose particles from the outside of the fixture with low-pressure compressed air.
3. Clean the surfaces by wiping gently with a soft, clean lint-free cloth moistened with a weak detergent solution. Do not rub glass surfaces hard: lift particles off with a soft repeated press. Dry with a soft, clean, lint-free cloth or lowpressure compressed air. Remove stuck particles with an unscented tissue or cotton swab moistened with glass cleaner or distilled water.
4. Check that the fixture is dry before reapplying power.
Replacing the primary fuse
If the fixture is completely dead, the fixture’s primary fuse F1 may have blown and it may be necessary to install a new fuse. This fuse is located in a fuseholder next to the MAINS OUT socket on the connections panel. See ‘Fixture overview’ on page 15.
If you need to replace a fuse:
1. Disconnect the fixture from power and allow it to cool for at least 10 minutes.
2. Unscrew the cap of the fuseholder and remove the fuse. Replace with a fuse of the same size and rating only.
3. Reinstall the fuseholder cap before reapplying power.
Service and repairs
There are no user serviceable parts inside the fixture. Do not open the housing.
Do not try to repair the fixture by yourself as this may result in damage, malfunction and it may potentially void your product warranty. The equipment must only be serviced or repaired by an authorized RUSH by Martin service technician.
Installation, on-site service and maintenance can be provided worldwide by the
Martin Professional Global Service organization and its approved agents, giving owners access to Martin’s expertise and product knowledge in a partnership that will ensure the highest level of performance throughout the product’s lifetime.
Please contact your RUSH by Martin supplier for details.
RUSH PAR 1 RGBW User Manual
27
advertisement
Related manuals
advertisement
Table of contents
- 5 Safety information
- 10 Introduction
- 10 Before using the product
- 11 Physical installation
- 11 Fastening the fixture to a flat surface
- 11 Mounting the fixture on a truss
- 12 Securing with a safety cable
- 13 AC power
- 14 Linking fixtures to power in a chain
- 15 Fixture overview
- 17 Control data link
- 17 Tips for reliable data transmission
- 18 Connecting the DMX data link
- 18 Fixture setup
- 18 Using the control menus
- 18 DMX addressing
- 19 DMX channel modes
- 19 Show mode
- 20 Dimmer modes
- 21 Sound activation (music trig)
- 21 Microphone sensitivity
- 21 DMX state
- 22 LED display on/off
- 22 LED display inversion
- 22 White balance adjustment
- 23 Manual mode
- 23 Auto test
- 24 Temperature readout
- 24 Fixture operating hours readout
- 24 Firmware version
- 25 Effects
- 25 Color control
- 25 Electronic dimming
- 25 Shutter/Strobe
- 26 Maintenance
- 26 Cleaning
- 27 Replacing the primary fuse
- 27 Service and repairs
- 28 DMX protocols
- 28 4-channel mode
- 28 5-channel mode
- 28 7-channel mode
- 30 Control menus
- 33 Troubleshooting
- 35 Specifications