PRIMERGY RX300 S7 Server Upgrade and Maintenance Manual

Basic hardware procedures

4.1.3.2

Local diagnostic indicators on the system board

F

Slot 6 PCIe x16

Slot 5 PCIe x16

VGA

Management

LAN

LAN 2

A

Shared

LAN

B

C

LAN

CTRL

H

G

H

Serial 1

USB

1/2

USB

3/4

F

Slot 4 PCIe x8 (mech. x16)

Slot 3 PCIe x4 (mech. x8)

NC-SI

Slot 2 PCIe x4 (mech. x8)

Slot 1 PCIe x4 (mech. x8)

Intrusion

HDD LED

1

JP1

CPU 2

CPU 2 DIMM 1G

CPU 2 DIMM 2G

CPU 2 DIMM 3G

CPU 2 DIMM 1H

CPU 2 DIMM 2H

CPU 2 DIMM 3H

CPU 2 DIMM 3F

CPU 2 DIMM 2F

CPU 2 DIMM 1F

CPU 2 DIMM 3E

CPU 2 DIMM 2E

CPU 2 DIMM 1E

BIOS-WP

F

K

I

PWR

PSU Control

L

PWR

HDD/ODD

Front VGA

Front LAN M

Front Panel

SMB 1

P

Battery

INDICATE

CSS iRMC

M N

TPM

USB

INT 2

USB

INT 1

/

FAN 5

O

CPU 1 DIMM 1A

CPU 1 DIMM 2A

CPU 1 DIMM 3A

CPU 1 DIMM 1B

CPU 1 DIMM 2B

CPU 1 DIMM 3B

FAN 4

O

H

O

CPU 1

CPU 1 DIMM 3D

CPU 1 DIMM 2D

CPU 1 DIMM 1D

CPU 1 DIMM 3C

CPU 1 DIMM 2C

CPU 1 DIMM 1C

G

H

FAN 3

FAN 2

O

JP8

PCH

Slot 7 PCIe x8 (RAID)

USB stick

SKU Key

SATA 1SATA 2

SMB 4

UFM

FAN 1

SAS 1-4

O

Figure 7: Onboard indicators and Indicate CSS button

No. Description

1 Indicate CSS button

Using the Indicate CSS button

Ê

Shut down and power off the server.

Ê

Disconnect the AC power cord from the system.

I

It is mandatory to disconnect power cords in order to use the Indicate

CSS functionality.

60 Upgrade and Maintenance Manual

RX300

Basic hardware procedures

Ê

Press the Indicate CSS button (1) to highlight defective components.

Component LEDs

I

LEDs A, B and C are visible from the outside on the server rear. All other

LEDs are only visible if the server cover has been opened. In order to access memory LEDs (D), the system fan module needs to be removed

(see section

"Removing a fan module" on page 172

).

Indicator Status

A

B

Identification

CSS

(Customer Self

Service) blue on

Description

server has been highlighted using the ID button on the front panel for easy identification blue flashing server has been highlighted using IRMC

(AVR) when local VGA off for easy identification no critical event (CSS component) off yellow on prefailure detected (CSS component) yellow flashing

CSS component failure off no critical event (non CSS component)

C

GEL

(Global Error

LED) orange on prefailure detected (non CSS component) non CSS component failure

Possible reasons: orange flashing

– sensors report overheating

– sensor is defective

– CPU error

– software reports an error orange on controller faulty

F

Controller

G

CPU

H

Memory module orange on orange on

I

PS CTRL OK green on

CPU faulty memory module faulty power supply OK

K

PS CTRL Error orange on powe supply error

L

Main power green on voltage ok

RX300 S7

Upgrade and Maintenance Manual 61