advertisement
![H. Care and maintenance. SCHUBERTH SR1 | Manualzz H. Care and maintenance. SCHUBERTH SR1 | Manualzz](http://s1.manualzz.com/store/data/005260574_1-ae99e26a6f24fe3d8c19cb38b787e37e-360x466.png)
h. CAre AnD mAintenAnCe
1. OUTER SHELL
To clean the helmet shell, you can use water, soapy water or one of the commonly available motorcycle shampoos, cleaners, polishes and plastic cleaners, or cleaning fluid. The use of water and soapy water is usually sufficient. Make sure when using the other cleaning materials that these do not come into contact with the visor, since these can cause damage to the visor and coating.
Warning:
Never use motor fuel, thinners, glass cleaner or other solvents to clean the helmet! Your helmet can be seriously damaged by these substances without visible damage.
Warning:
A helmet damaged or weakened by a cleaning agent may not provide head protection in an accident resulting in serious personal injury or death!
Warning:
Never use hot or salt water to clean the helmet. Your helmet can be seriously damaged by this treatment without damage.
2. FACE SHIELD
PINLOCK
®
VISOR
Outer surface of the Face Shield
Use a soft cloth and a mild soap solution (< 70 °F) to remove dirt from the outside of the Face Shield. To dry the Face Shield, use a lint-free cloth and apply gentle pressure.
44
h. CAre AnD mAintenAnCe
Inside surface of the Face Shield
The inside surface of the Face Shield must only be cleaned with a soft cloth, which may be slightly dampened if required (we recommend a mocrofibre cloth). Do not use any cleaning agents.
Note:
Only use warm water (< 70 °F) for cleaning. Never on any account clean the Face Shield or sun visor with gasoline, solvent, a window or glass cleaner or other cleaning agents containing alcohol.
3. INNER LINING
The headband cushion, the cheek comfort pads and the ear pads can be hand-washed using a mild detergent (best if well diluted with water) at a maximum temperature of 80 °F. Allow damp linings to dry at room temperature in airy conditions.
4. FASTENING SYSTEM
The double-D fastening system is maintenance-free.
Warning:
Do not oil or grease the metal parts of the double-D fastener.
5. STORAGE
Store the helmet in the pouch provided in a safe, dry place. To avoid buildup of moisture inside and to prolong the life of the anti-fog coating, ensure that the visor is not completely closed.
Ideally it should be set to the 2nd position above the urban mode setting. Always place the helmet so that it cannot fall onto the floor.
Note:
Keep the helmet out of reach of children and animals.
45
advertisement
Related manuals
advertisement
Table of contents
- 4 A. Correct use of this manual
- 5 B. Contents
- 7 C. Read first
- 12 D. The helmet
- 36 E. Putting the helmet on and taking it off
- 37 F. Before every ride
- 39 G. For your safety
- 45 H. Care and maintenance
- 47 I. Accessories and spare parts
- 48 J. After Sales Service
- 50 K. How to contact us
- 52 d'utiliser le manuel d'instructions
- 53 B. Sommaire
- 55 À lire en premier lieu
- 61 Le casque
- 86 Mettre et retirer le casque
- 87 Avant chaque utilisation
- 89 G. Pour votre sécurité
- 96 H. Entretien et soins
- 98 Accessoires et pièces détachées
- 101 K. Comment nous contacter
- 139 Antes de cada viaje
- 141 G. Para su seguridad
- 148 H. Mantenimiento y conservación
- 151 Accesorios y piezas de recambio
- 152 Servicio SCHUBERTH
- 154 K. Cómo contactarnos