Main Components. Fuji Xerox DocuPrint CP225 w

Below you will find brief information for Printer CP225 w. This guide provides operating information for the printer's print function. Explore features like easy wireless setup, manual duplex printing, and multiple up printing to conserve paper. Secure Print lets you temporarily store print data for later, and the wireless LAN feature lets you print without a wired connection. Understand the printer's components and menus to maximize use.

PDF

Document

Main Components



Front View

Operator Panel

Output Tray Extension

Toner Access Cover

Standard 150 Sheet Tray



Rear View

Center Output Tray

Print Head Cleaning Rod

Power Switch

Power Connector

USB Port

Rear Cover

Paper Chute

Transfer Belt

Rear Cover Handle

Ethernet Port

Transfer Roller

8 Paper Feed Roller

10 Levers

Basic Operation



Operator Panel

7 6

(

Power Saver

) button

(

Menu

) button buttons buttons

(

Stop

) button

(

Error

) indicator

(

Ready

) indicator

(

Back

) button

9 button

LCD panel

(

WPS

) button

(

Wi-Fi

) LED

Lights up in the sleep mode for the power saver mode. Press this button to exit the power saver mode.

Switches to the Menu mode from the print mode.

Scrolls through menus or items in the Menu mode. To enter numbers or passwords, press these buttons.

Selects submenus or setting values in the Menu mode.

Cancels the current print job or clears the value you entered.

Lights up when an error occurs and blinks when an unrecoverable error occurs.

Lights up when the printer is ready or the printer is in the low power mode for the power saver mode, and blinks when data is being received.

Switches to the print mode from the top menu of the Menu mode.

Returns to the upper hierarchy of the menu from the submenu of the Menu mode.

Displays the selected menu or item and determines the selected value in the

Menu mode.

Displays various settings, instructions, and error messages.

Starts Wi-Fi Protected Setup™ (Push Button Configuration).

Lights up when wireless connection is established, and blinks in certain conditions.

Basic Operation

Status of Wi-Fi LED

This section describes when the

See also:

•

"Wireless Problems" on page 155

(

Wi-Fi

) LED lights up or blinks.

(Wi-Fi) LED

Blinking normal

Blinking slowly

Wi-Fi settings

N/A

Printer Status

Off

Blinking fast

Off

Connected to the network via Ethernet cable; Regardless of the

Wi-Fi setting, wireless connection is not available when an Ethernet cable is connected to the printer

—

The printer enters the power saver mode

Failed to connect with Wireless LAN access point or router

Wireless link established

Searching/Connecting with wireless LAN access point or router

Searching/Connecting with WPS access point or router during wireless operation

Connecting with a mobile device using Wi-Fi Direct

Received an invitation from a mobile device to connect using Wi-Fi Direct

You can enable/disable the

Wi-Fi

settings. For more information, see "Wi-Fi" on page 111.

Basic Operation

Key features

Easy Wireless Connection Setup
Manual Duplex Print
Multiple Up Print
Secure Print
Wireless Print

Frequently asked questions

Connect the power cord to the power connector and the power source, then turn on/off the printer by pressing the power switch.

The printer supports A4, B5, A5, C5, Monarch, Com 10, DL, Letter, Legal, Folio, Executive, and custom sizes.

The document does not describe the process how to manually duplex print.

User questions

Robert C.

How to connect a printer to a wireless network using WPS-PIN?

Access the printer's Admin Menu. 2. Go to Network > WPS Setup > PIN Code. 3. Note the 8-digit PIN. 4. Start Configuration and select your wireless access point. 5. Enter the PIN into your access point within two minutes. A lit Wi-Fi LED confirms connection.

Mary N.

How to reset the camera?

To perform a factory reset, locate the reset button on the device, usually a small pinhole. Use a paperclip to press and hold the button for about 10-15 seconds until the indicator light changes, then release. The camera will then restart.

Patricia Q.

How to clean the CTD sensor?

To clean the Color Toner Density (CTD) sensor:

Open the toner access cover on the printer.
Locate the CTD sensor inside the printer.
Gently clean the CTD sensor with a soft, dry cloth. Be careful not to damage the sensor.
Close the toner access cover.

Mary N.

How to install the camera?

To install the camera, first ensure your Wi-Fi network is stable. Then, download the companion app from your app store, create an account, and follow the on-screen instructions to pair the camera. Mount the camera in your desired location using the provided mounting kit.

Mary N.

What is the purpose of the motion detection feature?

The motion detection feature allows the camera to automatically detect movement within its field of view and send instant alerts to your smartphone. Sensitivity settings and detection zones can be customized within the app.