Non-Genuine Mode. Fuji Xerox DocuPrint CP225 w

Below you will find brief information for Printer CP225 w. This guide provides operating information for the printer's print function. Explore features like easy wireless setup, manual duplex printing, and multiple up printing to conserve paper. Secure Print lets you temporarily store print data for later, and the wireless LAN feature lets you print without a wired connection. Understand the printer's components and menus to maximize use.

PDF

Document

Non-Genuine Mode

When toner within a toner cartridge is empty,

Replace XXXX Cartridge

(

XXXX

Yellow

Magenta

Cyan

, or

Black

) appears on the LCD panel.

When you want to use the printer in the Non-Genuine mode, enable the Non-Genuine mode and replace the toner cartridge.

IMPORTANT:

• If you use the printer in the Non-Genuine mode, the performance of the printer may not be at its optimum. Any problems that may arise from the use of the Non-Genuine mode are not covered by our quality guarantee. The continuous use of the Non-

Genuine mode can also cause the printer to break down, and any repair charges for such break down will be incurred by users.

NOTE:

• To disable the Non-Genuine mode, select

Off

for

Toner

Non-Genuine Mode

on the operator panel or deselect the check box next to

on the Non-Genuine Mode page on the Printer Setting Utility.



Using the Operator Panel

NOTE:

• Before starting the operation described below, confirm that

Ready to Print

is displayed on the LCD panel.

Press the (

Menu

) button.

Select

Admin Menu

, and then press the

Select

Maintenance

, and then press the

button.

button. Select

Non-Genuine Mode

, and then press the

Select

Toner

, and then press the button.

Select

, and then press the button.

The printer switches to the

Non-Genuine Mode



Using the Printer Setting Utility (Windows Only)

The following procedure uses Windows 7 as an example.

Click

Start



All Programs



Fuji Xerox



Fuji Xerox Printer Software for Asia-Pacific

 your printer 

Printer Setting Utility

NOTE:

• The window to select a printer appears in this step when multiple print drivers are installed on your computer. In this case, click the name of the desired printer listed in

Printer Name

The Printer Setting Utility opens.

Click the

Printer Maintenance

tab.

Select

Non-Genuine Mode

from the list at the left side of the page.

The

Non-Genuine Mode

page is displayed.

Select the check box next to

, and then click

Apply New Settings

164

Troubleshooting

Maintenance

•

"Cleaning the Printer" on page 166

"Replacing Toner Cartridges" on page 169

"Ordering Supplies" on page 173

"Storing Consumables" on page 174

"Managing the Printer" on page 175

"Conserving Supplies" on page 177

"Checking Page Counts" on page 178

"Moving the Printer" on page 179

Maintenance

165

Key features

Easy Wireless Connection Setup
Manual Duplex Print
Multiple Up Print
Secure Print
Wireless Print

Frequently asked questions

Connect the power cord to the power connector and the power source, then turn on/off the printer by pressing the power switch.

The printer supports A4, B5, A5, C5, Monarch, Com 10, DL, Letter, Legal, Folio, Executive, and custom sizes.

The document does not describe the process how to manually duplex print.

User questions

Robert C.

How to connect a printer to a wireless network using WPS-PIN?

Access the printer's Admin Menu. 2. Go to Network > WPS Setup > PIN Code. 3. Note the 8-digit PIN. 4. Start Configuration and select your wireless access point. 5. Enter the PIN into your access point within two minutes. A lit Wi-Fi LED confirms connection.

Mary N.

How to reset the camera?

To perform a factory reset, locate the reset button on the device, usually a small pinhole. Use a paperclip to press and hold the button for about 10-15 seconds until the indicator light changes, then release. The camera will then restart.

Patricia Q.

How to clean the CTD sensor?

To clean the Color Toner Density (CTD) sensor:

Open the toner access cover on the printer.
Locate the CTD sensor inside the printer.
Gently clean the CTD sensor with a soft, dry cloth. Be careful not to damage the sensor.
Close the toner access cover.

Mary N.

How to install the camera?

To install the camera, first ensure your Wi-Fi network is stable. Then, download the companion app from your app store, create an account, and follow the on-screen instructions to pair the camera. Mount the camera in your desired location using the provided mounting kit.

Mary N.

What is the purpose of the motion detection feature?

The motion detection feature allows the camera to automatically detect movement within its field of view and send instant alerts to your smartphone. Sensitivity settings and detection zones can be customized within the app.