Understanding the Printer Menus
This section describes menu options that can be accessed by pressing the panel.
(
Menu
) button on the operator
NOTE:
• The access to the operator panel menus can be limited with a password by enabling the Panel Lock function. For more
information, see "Panel Lock Function" on page 124.
Report / List
Use
Report / List
to print various types of reports and lists.
NOTE:
• A password is required to enter the operator panel menus when
Panel Lock Set is set to
Enable
. In this case, enter the password you specified, and press the button.
System Settings
Purpose:
To print a list of the information such as the printer name, serial number, and print volume.
Network settings are also printed.
Panel Settings
Purpose:
To print a detailed list of all the settings on the operator panel menus.
Job History
Purpose:
To print a detailed list of the jobs that have been processed. This list contains the last 50 jobs.
Error History
Purpose:
To print a detailed list of paper jams and fatal errors.
Demo Page
Purpose:
To print a test page.
PCL Fonts List
Purpose:
To print a sample of the available PCL fonts.
PS Fonts List
Purpose:
To print a sample of the available PS fonts.
Using the Operator Panel Menus
105
Stored Documents
NOTE:
• Stored Documents feature is available only when
RAM Disk
under
System Settings
is set to
On
.
Purpose:
To print a list of all files stored for Secure Print in the RAM disk.
Meter Readings
Use
Meter Readings
to check the total number of printed pages.
Values:
Meter 1
Meter 2
Meter 3
Meter 4
Displays the total number of color prints.
Displays the total number of monochrome prints.
Always shows
0
on your printer.
Displays the total number of color and monochrome prints (Meter 1 + Meter 2).
Admin Menu
Use
Admin Menu
to configure a variety of printer features.
NOTE:
• A password is required to enter the operator panel menus when
Panel Lock Set
is set to
Enable
. In this case, enter the password you specified, and then press the button.
Network
Use the
Network
menu to change the printer settings affecting jobs sent to the printer through the wired or wireless network.
NOTE:
• The value marked by an asterisk (*) is the factory default setting.
• Ethernet
Purpose:
To specify the communication speed and the duplex settings of Ethernet. The change becomes effective after the printer is turned off and then on.
Values:
Auto
*
10BASE-T Half
10BASE-T Full
100BASE-TX Half
100BASE-TX Full
Detects the Ethernet settings automatically.
Uses 10base-T half-duplex.
Uses 10base-T full-duplex.
Uses 100base-TX half-duplex.
Uses 100base-TX full-duplex.
NOTE:
• This item is displayed when the Ethernet cable is connected or
Wi-Fi
is set to
Off
.
106
Using the Operator Panel Menus
• Wi-Fi Status
Purpose:
To display the information on the wireless signal strength. No changes can be made on the operator panel to improve the status of the wireless connection.
Values:
Good
Acceptable
Low
No Reception
Indicates good signal strength.
Indicates marginal signal strength.
Indicates insufficient signal strength.
Indicates that no signal is received.
NOTE:
• This item is displayed when the Ethernet cable is disconnected and
Wi-Fi
is set to
On
.
• Wi-Fi Setup
Purpose:
To configure the wireless network interface. The printer automatically searches and list available access points.
Select one of the access points, and enter a passphrase or WEP key to complete the wireless setup. You can also specify and configure the wireless network manually.
Values:
Select Access
Manual Setup
Select the access point from the list. The access points are listed starting with the one in the best communication condition.
WEP Key
PassPhrase
Entry
Enter
NetworkSSID
Infrastructure
When you select an access point using WEP as the security method, enter the
WEP key. For 64bit keys, enter 10 hexadecimal characters. For 128bit keys, enter 26 hexadecimal characters.
When you select an access point using WPA™ (Wi-Fi Protected Access
®
) or
WPA2™, or Mixed as the encryption type, enter the passphrase of 8 to 63 alphanumeric (or 8 to 64 hexadecimal) characters.
Specify a name to identify the wireless network. Up to 32 alphanumeric characters can be entered.
Select to configure the wireless settings through the access point such as a wireless router.
No Security
Select to configure the wireless settings with no encryption settings.
Mixed Mode
PSK
Select to configure the wireless settings with the Mixed
Mode PSK encryption. Mixed Mode PSK automatically selects the encryption type from either WPA-PSK-AES or
WPA2-PSK-AES.
PassPhrase
Entry
Specify the passphrase of 8 to 63 alphanumeric (or 8 to 64 hexadecimal) characters.
WPA2-PSK-AES
WEP
Select to configure the wireless settings with the WPA2-
PSK-AES encryption.
PassPhrase
Entry
Specify the passphrase of 8 to 63 alphanumeric (or 8 to 64 hexadecimal) characters.
Select to configure the wireless settings with the WEP encryption.
WEP Key
Transmit
Key
Specify the WEP key to use through the wireless network. For 64bit keys, enter 10 hexadecimal characters. For 128bit keys, enter 26 hexadecimal characters.
Select a transmit key from
WEP Key 1
,
WEP Key 2
,
WEP Key 3
, and
WEP Key
4
.
Using the Operator Panel Menus
107
Ad-hoc
Select to configure the wireless settings without the access point such as a wireless router.
No Security
Select to configure the wireless settings with no encryption settings.
WEP
Select to configure the wireless settings with the WEP encryption.
WEP Key
Transmit
Key
Specify the WEP key to use through the wireless network. For 64bit keys, enter 10 hexadecimal characters. For 128bit keys, enter 26 hexadecimal characters.
Select a transmit key from
WEP Key 1
,
WEP Key 2
,
WEP Key 3
, and
WEP Key
4
.
NOTE:
• This item is displayed when the Ethernet cable is disconnected and
Wi-Fi
is set to
On
.
• WPS Setup
Purpose:
To configure the wireless network using Wi-Fi Protected Setup™ (WPS).
Values:
PushButtonControl
PIN Code
Configures the wireless settings with WPS-PBC
*1
.
Start
Configuration
Configures the wireless settings using WPS-PIN
*2
assigned automatically by the printer.
Print PIN Code
Prints the PIN code. Confirm it when you enter the PIN code to your computer.
*1
WPS-PBC stands for Wi-Fi Protected Setup-Push Button Configuration.
*2
WPS-PIN stands for Wi-Fi Protected Setup-Personal Identification Number.
NOTE:
•
•
Instead of selecting
PushButtonControl
, you can also start WPS-PBC by pressing and holding the (
WPS
) button.
WPS 2.0 compliant. WPS 2.0 works on access points with the following encryption types: Mixed Mode PSK, WPA-PSK-AES,
WPA2-PSK-AES, Open (No Security)
• This item is displayed when the Ethernet cable is disconnected and
Wi-Fi
is set to
On
.
• Wi-Fi Direct Setup
Purpose:
To configure the Wi-Fi Direct
®
settings.
Values:
Wi-Fi Direct
Group Role
Device Name
Connection
Status
SSID
Disable
*
Enable
Group Owner
*
Auto
Displays the device name.
No Entry
Device name
Disables the Wi-Fi Direct connection.
Enables the Wi-Fi Direct connection.
Sets your printer as the group owner for Wi-Fi Direct.
Automatically resolves the group role for Wi-Fi Direct.
Current Role
Current SSID
EnterNetworkSSID
Indicates that no device is available.
Disconnect
Disconnects the connected device when using
Wi-Fi Direct.
Reset
Passphrase
Disconnects the connected device and reset passphrase when using Wi-Fi Direct.
Displays the current role of the printer.
Displays the current SSID of the connected wireless network.
Displays SSID of the printer. You can specify the name to identify the wireless network.
108
Using the Operator Panel Menus
PassPhrase Show Passphrase
Print Passphrase
Displays the passphrase. Confirm it when you enter the passphrase to your mobile device.
Prints the passphrase. Confirm it when you enter the passphrase to your mobile device.
WPS Setup
PIN Code
*1
Reset Passphrase
PushButtonControl
PIN Code
Print PIN Code
Resets the passphrase.
Configures the Wi-Fi Direct settings with the security method of WPS-
PBC.
Configures the Wi-Fi Direct settings using the PIN code to your mobile device.
Prints the PIN code. Confirm it when you enter the PIN code to your mobile device.
Reset PIN Code
Resets the PIN code.
*1
This item is displayed when
Wi-Fi Direct
is set to
Enable
and
WPS Setup
is set to
PIN Code
.
NOTE:
• This item is displayed when the Ethernet cable is disconnected and
Wi-Fi
is set to
On
.
• Reset Wi-Fi
Purpose:
To reset the wireless connection settings. After executing this function, all information about the access point is cleared.
NOTE:
• This item is displayed when the Ethernet cable is disconnected and
Wi-Fi
is set to
On
.
• TCP/IP
Purpose:
To configure TCP/IP settings. The change becomes effective after the printer is turned off and then on.
Values:
IP Mode Dual Stack
*
IPv4 Mode
Uses both IPv4 and IPv6 to set the IP address.
Uses IPv4 to set the IP address.
IPv4 Ethernet
IPv4 Wi-Fi
/
Get IP
Address
DHCP/AutoIP
*
BOOTP
Automatically sets the IP address.
Uses BOOTP to set the IP address.
RARP
DHCP
Uses RARP to set the IP address.
Uses DHCP to set the IP address.
IP Address
Panel
Enables the IP address entered on the operator panel.
Manually sets the IP address allocated to the printer.
Subnet Mask
Gateway Address
Manually sets the subnet mask.
Manually sets the gateway address.
IPv4 Wi-Fi
Direct
IP Address
Displays the IPv4 address allocated to the printer when using
Wi-Fi Direct.
IPsec
*
1
Subnet Mask
Disable
*
Displays the subnet mask when using Wi-Fi Direct.
Disables the IPsec.
Enable
Enables the IPsec.
*1
This item is displayed when the IPsec is enabled on the CentreWare Internet Services.
NOTE:
• To set an IP address for IPv6 in Dual Stack mode, use the CentreWare Internet Services. For more information, refer to the online Help on the CentreWare Internet Services.
Using the Operator Panel Menus
109
• Protocol
Purpose:
To enable or disable each protocol. The change becomes effective after the printer is turned off and then on.
Values:
LPD
Port 9100
IPP
*
1
Enable
*
Disable
Enable
*
Disable
Enable
*
Disable
Enable
*
Disable
Enables the LPD port.
Disables the Line Printer Daemon (LPD) port.
Enables the Port 9100 port.
Disables the Port 9100 port.
Enables IPP.
Disables IPP.
WSD
(Web Services on
Devices)
Enables the Web Services on Devices (WSD) port.
Disables the Web Services on Devices (WSD) port.
SNMP v1/v2c Enable
* Enables SNMP v1/v2c.
Status
Messenger
Internet
Services
Bonjour(mDNS)
Disable
Enable
Enable
*
Disable
*
Disable
Enable
*
Disables SNMP v1/v2c.
Enables Status Messenger.
Disables Status Messenger.
Enables Internet Services.
Disables Internet Services.
Enables Bonjour (mDNS).
HTTP-SSL/TLS
*2
Disable
Enable
*
Disables Bonjour (mDNS).
Enables HTTP-SSL/TLS.
Google Cloud
Print
Disable
Disable
Enable
*
Disables HTTP-SSL/TLS.
Disables Google Cloud Print™.
Enables Google Cloud Print.
*1
To add a printer using an IPP port on Windows
®
, insert port number "631" in the URL of the printer.
For example: http:// [Printer's IP address]:631/ipp
*2
HTTP-SSL/TLS
is displayed when a certificate is created using the CentreWare Internet Services. For details about creating a certificate, see the Help on the CentreWare Internet Services.
• IP Filter
Purpose:
To block data received from certain IP addresses through the wired or wireless network. You can set up to five IP addresses.
Values:
No.n/Address
( n
is 1 – 5.)
No.n/Mask
( n
is 1 – 5.)
No.n/Mode
( n
is 1 – 5.)
Sets the IP address for Filter n
.
Sets the address mask for Filter n
.
Off
*
Accept
Reject
Disables the feature for Filter n
.
Accepts an access from the specified IP address.
Rejects an access from the specified IP address.
NOTE:
• This item is only available for
LPD
or
Port 9100
.
• Initialize NVM
Purpose:
To initialize network data stored in Non-Volatile Memory (NVM). After executing this function and rebooting the printer, all network settings are reset to their default values.
110
Using the Operator Panel Menus
• PS Data Format
Purpose:
To specify the PostScript 3 Compatible communication protocol for a parallel interface, you can configure the
PS
Data Format
settings for the wired network. The change becomes effective after the printer is turned off and then on again.
Values:
Auto
*
Standard
BCP
TBCP
Sets the PostScript 3 Compatible communications protocol automatically.
Sets the PostScript 3 Compatible communications protocol to
Standard
.
Sets the PostScript 3 Compatible communications protocol to
BCP
.
Sets the PostScript 3 Compatible communications protocol to
TBCP
.
• Wi-Fi
Purpose:
To enable the wireless connection. The change becomes effective after the printer is turned off and then on.
Values:
On
*
Off
Enables the wireless connection.
Disables the wireless connection.
NOTE:
• This item is displayed only when the Ethernet cable is disconnected.
• When you use the USB connection and do not use the wireless connection, you need to set
Wi-Fi
to
Off
.
System Settings
Use the
System Settings
menu to specify the various basic settings for the printer.
NOTE:
• The value marked by an asterisk (*) is the factory default setting.
• Power Saver Timer
Purpose:
To specify the time for transition to the power saver mode.
Values:
Low Power
Timer
Sleep Timer
5min*
5 – 30min
6min*
1 – 6min
Specifies the time taken by the printer to enter the low power mode after it finishes a job.
Specifies the time taken by the printer to enter the sleep mode after it has entered the low power mode.
Select
5min
(default) for Low Power Timer if your printer shares an electrical circuit with your room lights and you notice them flickering. Otherwise, select a high value to keep your printer available for frequent use with the minimum warm-up time.
The printer automatically returns to the standby mode from the power saver mode when it receives data from the computer. In Low Power Timer, you can also change the status of the printer to the standby mode by pressing any button on the operator panel. In Sleep Timer, you can change the status of the printer to the standby mode by pressing the (
Power Saver
) button on the operator panel.
Using the Operator Panel Menus
111
• Auto Reset
Purpose:
To specify the time for the printer to automatically return to the standby mode. When the setting is not complete in the specified time, the previous setting is restored.
Values:
45sec
*
1min
2min
3min
4min
• Fault Timeout
Purpose:
To specify the time taken by the printer before it cancels jobs that stop abnormally. The print job is canceled if it times out.
Values:
On 60sec
*
3 – 300sec
Specifies the time taken by the printer before it cancels for jobs that stop abnormally.
Disables the fault timeout.
Off
• Job Timeout
Purpose:
To specify the amount of time that the printer waits for data to arrive from the computer. The print job is canceled if it times out.
Values:
On 30sec
*
5 – 300sec
Specifies the amount of time that the printer waits for data to arrive from the computer.
Disables the job timeout.
Off
• mm / inch
Purpose:
To specify the measurement unit displayed after the numeric value on the operator panel.
Values:
Millimeters(mm)
*
Inches(")
Selects millimeter as the measurement unit.
Selects inch as the measurement unit.
• LowTonerAlertMsg
Purpose:
To specify whether to show the alert message when the toner is low.
Values:
On
*
Off
Shows the alert message when the toner is low.
Does not show the alert message when the toner is low.
112
Using the Operator Panel Menus
• PaperSzeMismatch
Purpose:
To specify whether to use paper of a different size when the paper that is loaded in the standard 150 sheet tray does not match the paper size settings for the current job.
Values:
On(except A4/Ltr)
*
Off
On
Shows the alert message except for the time A4 size paper is loaded in the tray and Letter size is set for the current job and for the other way around.
No tray size substitute accepted.
Shows the alert message when the paper size loaded in the tray is different from the paper size set for the current job.
• RAM Disk
Purpose:
To allocate memory to the RAM disk file system for the Secure Print features. The change becomes effective after the printer is turned off and then on again.
Values:
Off
*
On
Does not allocate memory to the RAM disk file system. Secure Print jobs will abort and be recorded to the job log.
Sets the allocation of memory to the RAM disk file system.
Maintenance
Use the
Maintenance
menu for maintenance work including initialization of the NVM (non-volatile memory).
NOTE:
• The value marked by an asterisk (*) is the factory default setting.
• F/W Version
Purpose:
To display the version of the controller.
• Adjust Paper Type
Purpose:
To adjust the paper type.
Values:
Plain
Labels
Heavyweight
*
Lightweight
Heavyweight
*
Lightweight
Using the Operator Panel Menus
113
• Adjust BTR
Purpose:
To specify the optimum voltage settings for printing for the transfer roller (BTR). To lower the voltage, set negative values. To increase, set positive values.
The default settings may not give the best output on all paper types. If you see mottles on the print output, try to increase the voltage. If you see white spots on the print output, try to decrease the voltage.
NOTE:
• The print quality changes depending on the values you select for this item.
Values:
Plain
Bond
Light Card
LW Gloss Card
Labels
Recycled
Envelope
0
*
-3 – 3
0
*
-3 – 3
0
*
-3 – 3
0
*
-3 – 3
0
*
-3 – 3
0
*
-3 – 3
0
*
-3 – 3
• Adjust Fusing Unit
Purpose:
To specify the optimum temperature settings for printing for the fusing unit. To lower the temperature, set negative values. To increase, set positive values.
The default settings may not give the best output on all paper types. When the printed paper has curled, try to lower the temperature. When the toner does not fuse on the paper properly, try to increase the temperature.
NOTE:
• The print quality changes depending on the values you select for this item.
Values:
Plain
Bond
Light Card
LW Gloss Card
Labels
Recycled
Envelope
0
*
-3 – 3
0
*
-3 – 3
0
*
-3 – 3
0
*
-3 – 3
0
*
-3 – 3
0
*
-3 – 3
0
*
-3 – 3
114
Using the Operator Panel Menus
• Auto Regi Adjust
Purpose:
To automatically start adjusting color registration.
Values:
On
*
Off
Automatically adjusts color registration.
Does not automatically adjust color registration.
• Adjust ColorRegi
Purpose:
To start adjusting color registration when you need.
Color registration adjustments are required when the printer is initially installed and after the printer is moved.
Values:
Auto Adjust
Automatically performs color registration correction.
• Clean Developer
Purpose:
To rotate the developer motor and stir the toner in the toner cartridge.
• Toner Refresh
Purpose:
To use up a toner cartridge when you need to replace it before the end of its life, or to stir the toner in a new toner cartridge.
Values:
Yellow
Magenta
Cyan
Black
Cleans the toner in the yellow toner cartridge.
Cleans the toner in the magenta toner cartridge.
Cleans the toner in the cyan toner cartridge.
Cleans the toner in the black toner cartridge.
• BTR Refresh
Purpose:
To specify whether to execute counter measures for curling/separating discharge of the paper.
Values:
Off
*
On
Does not automatically execute counter measures for curling/separating discharge of the paper.
Automatically executes counter measures for curling/separating discharge of the paper.
• Initialize NVM
Purpose:
To initialize NVM for system parameters. After executing this function and rebooting the printer, the menu parameters, except the parameters for the network, are reset to their factory default values.
See also:
•
"Resetting to Factory Defaults" on page 126
Using the Operator Panel Menus
115
• Non-Genuine Mode
Purpose:
To use toner cartridges of another manufacturer.
NOTE:
•
•
Using non-genuine toner cartridges may make some printer features unusable, reduce print quality and decrease the reliability of your printer. Fuji Xerox recommends only new Fuji Xerox brand toner cartridges for your printer. Fuji Xerox does not provide warranty coverage for problems caused by using accessories, parts, or components not supplied by Fuji Xerox.
Before you use toner cartridges of another manufacturer, be sure to restart the printer.
Values:
Toner Off
*
On
Does not use toner cartridges of another manufacturer.
Uses toner cartridges of another manufacturer.
• Adjust Altitude
Purpose:
To specify the altitude of the location where the printer is installed.
The discharge phenomenon for charging the photo conductor varies with barometric pressure. Adjustments are performed by specifying the altitude of the location where the printer is being used.
NOTE:
• An incorrect altitude adjustment setting leads to problems such as poor printing quality and incorrect indication of remaining toner.
Values:
0m
*
1000m
2000m
3000m
Specifies the altitude of the location where the printer is installed.
• Machine Life
Purpose:
To specify whether to continue print operations when the printer comes to the end of its service life.
Values:
Stop Print
*
Continue Print
Stops print operations at the end of service life.
Continues print operations after the end of service life.
NOTE:
• When the printer no longer operates showing the error code 191-310 on the LCD panel, press the (
Back
) button and the
button at the same time and change the
Machine Life
setting to
Continue Print
. Then, you can keep using the printer.
• Although you can keep using the printer after the end of its service life by changing the setting to
Continue Print
, the printing quality is not guaranteed.
Secure Settings
Use the
Secure Settings
menu to set a password to limit access to the menus. This prevents items from being changed accidentally.
NOTE:
• The value marked by an asterisk (*) is the factory default setting.
116
Using the Operator Panel Menus
• Panel Lock
Purpose:
To restrict access to the operator panel menus and change the password.
See also:
•
"Panel Lock Function" on page 124
Values:
Panel Lock Set
Change Password
*
1
Disable
*
Enable
Does not restrict access to the operator panel menus.
Restricts access to the operator panel menus with a password.
Change the password set to access the operator panel menus.
*1
This item is displayed when
Panel Lock Set
is set to
Enable
.
• Software Download
Purpose:
To enable or disable download of firmware updates.
Values:
Enable
*
Disable
Enables firmware updates.
Disables firmware updates.
• Show Network Info
Purpose:
To show or hide network information on the LCD panel.
Values:
IP Address
*
Host Name
Hide Information
Shows the IP address of the printer.
Shows the host name of the printer.
Does not show network information.
USB Settings
Use the
USB Settings
menu to change printer settings affecting a USB port.
NOTE:
• The value marked by an asterisk (*) is the factory default setting.
• Port Status
Purpose:
To change the USB settings on your printer.
Values:
Enable
*
Disable
Enables the USB interface.
Disables the USB interface.
Using the Operator Panel Menus
117
• PS Data Format
Purpose:
To specify the PostScript 3 Compatible communication protocol for a parallel interface, you can configure the
PS
Data Format
settings for the wired network.
Values:
Auto
*
Standard
BCP
TBCP
Sets the PostScript 3 Compatible communications protocol automatically.
Sets the PostScript 3 Compatible communications protocol to
Standard
.
Sets the PostScript 3 Compatible communications protocol to
BCP
.
Sets the PostScript 3 Compatible communications protocol to
TBCP
.
PCL Settings
Use the
PCL Settings
menu to change printer settings that only affect jobs using the PCL emulation printer language.
NOTE:
• The value marked by an asterisk (*) is the factory default setting.
• Paper Size
Purpose:
To specify the default paper size.
Values:
A4 - 210
297
*
1
A5 - 148
210
B5 - 182
257
Letter - 8.5
11
Folio - 8.5
13
Legal - 8.5
14
Executive
#10 Env - 4.1
9.5
Monarch Env.
Monarch Env. L
DL Env - 110
220
DL Env L
C5 Env - 162
229
New Custom Size Portrait(Y)
*
2
Landscape(X)
*
2
297 mm
*
127 – 355 mm
210 mm
*
Portrait(Y)
*
3
77 – 215 mm
11.7 inch
*
5.0 – 14.0 inch
8.3 inch
*
Landscape(X)
*
3
3.0 – 8.5 inch
*1
*2
*3
The default for
Paper Size
varies depending on region-specific factory default.
The item is displayed when mm / inch
is set to
Millimeters (mm)
.
The item is displayed when mm / inch
is set to
Inches (")
.
Specifies the length of the custom size paper.
Specifies the length of the custom size paper.
Specifies the length of the custom size paper.
Specifies the length of the custom size paper.
NOTE:
• Selecting
New Custom Size
for the paper size prompts you to enter a custom length and width.
118
Using the Operator Panel Menus
• Orientation
Purpose:
To specify how text and graphics are oriented on the page.
Values:
Portrait
*
Landscape
Courier
*
CGTimes
CGTimesBd
CGTimesIt
CGTimesBdIt
CGOmega
CGOmegaBd
CGOmegaIt
CGOmegaBdIt
Coronet
ClarendonCd
UniversMd
UniversBd
UniversMdIt
UniversBdIt
UniversMdCd
UniversBdCd
UniversMdCdIt
UniversBdCdIt
AntiqueOlv
AntiqueOlvBd
AntiqueOlvIt
GarmondAntiqua
GarmondHlb
GarmondKrsv
GarmondKrsvHlb
Marigold
Prints text and graphics parallel to the short edge of the paper.
Prints text and graphics parallel to the long edge of the paper.
• Font
Purpose:
To specify the default font from the fonts registered in the printer.
Values:
AlbertusMd
AlbertusXb
Arial
ArialBd
ArialIt
ArialBdIt
TimesNew
TimesNewBd
TimesNewIt
TimesNewBdIt
Helvetica
HelveticaBd
HelveticaOb
HelveticaBdOb
HelveticaNr
HelveticaNrBd
HelveticaNrOb
HelveticaNrBdOb
PalatinoRmn
PalatinoBd
PalatinoIt
PalatinoBdIt
ITCAvantGardBk
ITCAvantGardDb
ITCAvantGardBkOb
ITCAvantGardDbOb
ITCBookmanLt
ITCBookmanDb
ITCBookmanLtIt
ITCBookmanDbIt
NwCentSchlbkRmn
NwCentSchlbkBd
NwCentSchlbkIt
NwCentSchlbkBdIt
Times
TimesBd
TimesIt
TimesBdIt
ZapfChanceryMdIt
Symbol
SymbolPS
Wingdings
ZapfDingbats
CourierBd
CourierIt
CourierBdIt
LetterGothic
LetterGothicBd
LetterGothicIt
CourierPS
CourierPSBd
CourierPSOb
CourierPSBdOb
Line Printer
• Symbol Set
Purpose:
To specify a symbol set for a specified font.
Values:
PC-8
*
PC-8 DN
PC-850
PC-852
PS MATH
PI FONT
LEGAL
ISO-4
WINGDINGS
DNGBTSMS
ISO-L6
PC-1004
Using the Operator Panel Menus
119
PC-8 TK
WIN L1
WIN L2
WIN L5
DESKTOP
MC TEXT
PS TEXT
MS PUB
MATH-8
ISO-6
ISO-11
ISO-15
ISO-17
ISO-21
ISO-60
ISO-69
WIN 3.0
SYMBOL
PC-775
WINBALT
UCS-2
ROMAN-8
ROMANEXT
ISO-L1
ISO-L2
ISO-L5
• Font Size
Purpose:
To specify the font size for scalable typographic fonts, within the range of 4.00 to 50.00. The default is 12.00. Font size refers to the height of the characters in the font. One point equals approximately 1/72 of an inch.
NOTE:
• The
Font Size
menu is only displayed for typographic fonts.
• Font Pitch
Purpose:
To specify the font pitch for scalable mono spaced fonts, within the range of 6.00 to 24.00. The default is 10.00.
Font pitch refers to the number of fixed-space characters in a horizontal inch of type. For nonscheduled mono spaced fonts, the pitch is displayed, but cannot be changed.
NOTE:
• The
Font Pitch
menu is only displayed for fixed or mono spaced fonts.
• Form Line
Purpose:
To set the number of lines in a page.
Values:
64
*1
5 – 128
Sets the value in increments of 1.
*1
The default for
Form Line
varies depending on the default paper size.
The printer sets the amount of space between each line (vertical line spacing) based on the
Form Line
and
Orientation
menu items. Select the correct
Form Line
and
Orientation
before changing
Form Line
.
See also:
•
"Orientation" on page 119
• Quantity
Purpose:
To specify the number of copies to print.
Values:
1
*
1 – 999
Sets the value in increments of 1.
120
Using the Operator Panel Menus
• Draft Mode
Purpose:
To save toner by printing in the draft mode. The print quality is reduced when you print in the draft mode.
Values:
Disable
*
Enable
• Line Termination
Purpose:
To add the line termination commands.
Values:
Off
*
Carriage Return
Line Feed
CR + LF
Does not print in the draft mode.
Prints in the draft mode.
The line termination command is not added.
CR=CR, LF=LF, FF=FF
The CR command is added.
CR=CR, LF=CR-LF, FF=CR-FF
The LF command is added.
CR=CR-LF, LF=LF, FF=FF
The CR and LF commands are added.
CR=CR-LF, LF=CR-LF, FF=CR-FF
• Output Color
Purpose:
To specify the output color.
Values:
Color
*
Black & White
Prints in the color mode.
Prints in the black and white mode.
PS Settings
Use the
PS Settings
menu to change printer settings that only affect jobs using the PostScript 3 Compatible printer language.
NOTE:
• The value marked by an asterisk (*) is the factory default setting.
• PS Error Report
Purpose:
To specify whether to print the contents of PostScript 3 Compatible errors.
Values:
On
*
Off
Prints an error message before it discards the job.
Discards the print job without printing an error message.
NOTE:
• Instructions from the PS driver override the settings specified on the operator panel.
Using the Operator Panel Menus
121
• PS Job Timeout
Purpose:
To specify the runtime of one PostScript 3 Compatible job.
Values:
Off
*
On 1min
1 – 900min
• Output Color
Purpose:
To specify the output color.
Values:
Job timeout does not occur.
A PostScript 3 Compatible error occurs if processing is not completed after the specified time.
Color
*
Black & White
Prints in color mode.
Prints in black and white mode.
• Image Depth
Purpose:
To specify the image depth setting to 1 bit or 2 bit.
Values:
2 Bit
*
1 Bit
Prints in 2 bit color.
Prints in 2 bit color or if you use the other PS driver not provided with this printer, it prints in 1 bit color.
PDF Settings
Use the
PDF Settings
menu to change printer settings that only affect the PDF jobs.
NOTE:
• The value marked by an asterisk (*) is the factory default setting.
• Quantity
Purpose:
To specify the number of copies to print.
Values:
1
*
1 – 999
• Print Mode
Purpose:
To specify the print mode.
Values:
Normal
*
High Quality
Sets the value in increments of 1.
For documents with normal sized characters.
For documents with small characters or thin lines, or documents printed using a dot-matrix printer.
122
Using the Operator Panel Menus
• PDF Password
Purpose:
To specify the password to print the secure PDF.
Values:
PDF Password
• Output Size
Purpose:
To specify the output paper size for PDF.
Values:
Enter the password to print the secure PDF.
Auto
*
A4 - 210
297
A5 - 148
210
B5 - 182
257
Letter - 8.5
11
Folio - 8.5
13
Legal - 8.5
14
Executive
• Layout
Purpose:
To specify the output layout.
Values:
Auto
*
100
%
(No Zoom)
2 Pages Up
4 Pages Up
• Output Color
Purpose:
To specify the output color.
Values:
Color
*
Black & White
Prints in color mode.
Prints in black and white mode.
Using the Operator Panel Menus
123
