Setting the IP Address (for IPv4 Mode). Fuji Xerox DocuPrint CP225 w

Below you will find brief information for Printer CP225 w. This guide provides operating information for the printer's print function. Explore features like easy wireless setup, manual duplex printing, and multiple up printing to conserve paper. Secure Print lets you temporarily store print data for later, and the wireless LAN feature lets you print without a wired connection. Understand the printer's components and menus to maximize use.

PDF

Document

Setting the IP Address (for IPv4 Mode)

NOTE:

• To set an IP address for IPv6 in Dual Stack mode, use the CentreWare Internet Services. For more information, refer to the online Help on the CentreWare Internet Services. To display the CentreWare Internet Services in an IPv6 network, use a link

local address. The printer's link local address is listed in the System Settings page. For details, see “Printing and Checking the

System Settings Page” on page 43.



Printer's TCP/IP and IP Addresses

If your computer is on a large network, contact your network administrator for the appropriate TCP/IP addresses and additional system settings information.

If you are creating your own small local area network or connecting the printer directly to your computer using network, follow the procedure for automatically setting the printer's IP address.

Computers and printers primarily use TCP/IP protocols to communicate over a network. With TCP/IP protocols, each printer and computer must have a unique IP address. It is important that the addresses are similar, but not the same; only the last digit needs to be different. For example, your printer can have the address 192.0.2.1 while your computer has the address 192.0.2.2. Another device can have the address 192.0.2.3.

Many networks have a Dynamic Host Configuration Protocol (DHCP) server. A DHCP server automatically programs an IP address into every computer and printer on the network that is configured to use DHCP. A DHCP server is built into most cable and Digital Subscriber Line (DSL) routers. If you use a cable or DSL router, see your router's documentation for information on IP addressing.



Dynamic Methods of Setting the Printer's IP Address

The DHCP and AutoIP protocols are available for dynamically setting the printer's IP address. They are enabled by default in your printer.

You can turn on/off both protocols using the operator panel or the CentreWare Internet Services.

NOTE:

•

You can print a report that includes the printer's IP address. For more information, refer to "Printing and Checking the System

Settings Page" on page 43.

Using the Operator Panel

Press the (

Menu

) button.

Select

Admin Menu

, and then press the

Select

Network

, and then press the

button.

Select

TCP/IP

, and then press the button.

Select

IPv4 Ethernet

IPv4 Wi-Fi

, and then press the

Select

Get IP Address

, and then press the

Select

DHCP/AutoIP

, and then press the

button.

Turn off and turn on the printer.

button.

Printer Connection and Software Installation

Using the CentreWare Internet Services

Launch your web browser.

Enter the IP address of the printer in the address bar, and then press the

Enter

key.

Select

Properties

Select

TCP/IP

from the

Protocol Settings

folder on the left navigation panel.

In the

IP Address Mode

field under

IPv4

, select the

DHCP/AutoIP

option.

Click

Apply

Click

Reboot Machine

to restart the printer.



Assigning an IP Address Manually

NOTE:

• Assigning an IP address is considered as an advanced function and is normally performed by a system administrator.

• Depending on the address class, the range of the IP address assigned may be different. On Class A, for example, an IP address in the range from

0.0.0.0

127.255.255.255

will be assigned. For assignment of IP addresses, contact your system administrator.

You can assign the IP address by using the operator panel, the Printer Setting Utility, or the CentreWare Internet

Services.

For Windows, you can also assign the IP address to the printer using the installer on the

Software Pack CD-ROM

Using the Operator Panel

Press the (

Menu

) button.

Select

Admin Menu

, and then press the

Select

Network

, and then press the

button.

Select

TCP/IP

, and then press the button.

Select

IPv4 Ethernet

IPv4 Wi-Fi

, and then press the

Select

Get IP Address

, and then press the button.

Select

Panel

, and then press the

Press the (

Back

) button.

button.

Confirm that

Get IP Address

appears.

Select

IP Address

, and then press the button.

The first three digits of the IP address are selected.

button.

Enter the value using the or button.

Press the button.

The next three digits are selected.

Repeat steps

to set all digits in the IP address, and then press the

Press the (

Back

) button.

Confirm that

IP Address

appears.

button.

Printer Connection and Software Installation

Select

Subnet Mask

, and then press the button.

The first three digits of the subnet mask are selected.

Enter the value using the or button.

Press the button.

The next three digits are selected.

Repeat steps

to set subnet mask, and then press the

Press the (

Back

) button.

Confirm that

Subnet Mask

appears.

Select

Gateway Address

, and then press the button.

The first three digits of the gateway address are selected.

Enter the value of the gateway address using the or button.

Press the button.

The next three digits are selected.

Repeat steps

to set gateway address, and then press the

Turn off and turn on the printer.

See also:

•

"Operator Panel" on page 18

button.

Using the Printer Setting Utility (Windows Only)

The following procedure uses Windows 7 as an example.

Click

Start



All Programs



Fuji Xerox



Fuji Xerox Printer Software for Asia-Pacific

 your printer 

Printer Setting Utility

NOTE:

• The window to select a printer appears in this step when multiple print drivers are installed on your computer. In this case, click the name of the desired printer listed in

Printer Name

The Printer Setting Utility appears.

Click the

Printer Maintenance

tab.

Select

TCP/IP Settings

from the list at the left side of the page.

The

TCP/IP Settings

page is displayed.

Select

Panel

from

IP Address Mode

, and then enter the values in

IP Address

Subnet Mask

, and

Gateway

Address

Click

Restart printer to apply new settings

to take effect.

Printer Connection and Software Installation

Using the Installer on the Software Pack CD-ROM (Windows Only)

You can assign the IP address to the printer when setting up the printer with the installer on the

Software Pack CD-

ROM

When you use the Ethernet or the manual Wireless setup method, and

Get IP Address

is set to

DHCP/AutoIP on the operator panel menu, the installer detects the printer by the automatically assigned IP address. You can modify the assigned IP address to the desired IP address by clicking

Advanced

on the

Configure Printer

screen while in the setup process.

See also:

•

"Dynamic Methods of Setting the Printer's IP Address" on page 39

The IP address is assigned to your printer. To verify the setting, display the web browser on any computer connected to the network and enter the IP address into the address bar on the browser. If the IP address is set up correctly, the

CentreWare Internet Services is displayed in your browser.



Verifying the IP Settings

You can confirm the settings by printing the System Settings page or using the ping command.

Printing the System Settings Page

Print the System Settings page.

See also:

•

"Printing a System Settings Page" on page 101

Look under the

IPv4

heading of

TCP/IP

on the

Wired Network

Wireless Network

section of the System

Settings page to confirm that the IP address, subnet mask, and gateway address are appropriate.

If the IP address is

0.0.0.0

(the factory default) or

169.254.xx.xx

, an IP address has not been assigned.

Using the Ping Command

To verify if the printer is active on the network, run the ping command in your computer.

The following procedure uses Windows 7 as an example.

Click

Start



All Programs



Accessories



Run

Enter "cmd", and then click

The

Command Prompt

window is displayed.

Enter "ping xxx.xxx.xxx.xxx" (xxx.xxx.xxx.xxx is the IP address of your printer), and then press the

Enter

key.

Receiving the reply from the printer IP address means that the printer is appropriately connected to the network.

Printer Connection and Software Installation



Printing and Checking the System Settings Page

Print the System Settings page and check your printer's IP address.

Using the Operator Panel

Print the System Settings page.

See also:

•

"Printing a System Settings Page" on page 101

Confirm the IP address next to

IP Address

under

Wired Network

Wireless Network

on the System

Settings page.

If the IP address is

0.0.0.0

, wait for a few minutes to resolve the IP address automatically, and then print the

System Settings page again.

If the IP address is not resolved automatically, see "Assigning an IP Address Manually" on page 40.

Using the Printer Setting Utility (Windows Only)

Print the System Settings page.

See also:

•

"Printing a System Settings Page" on page 101

If the IP address is

0.0.0.0

(the factory default) or

169.254.xx.xx

, an IP address has not been assigned.

Printer Connection and Software Installation

Key features

Easy Wireless Connection Setup
Manual Duplex Print
Multiple Up Print
Secure Print
Wireless Print

Frequently asked questions

Connect the power cord to the power connector and the power source, then turn on/off the printer by pressing the power switch.

The printer supports A4, B5, A5, C5, Monarch, Com 10, DL, Letter, Legal, Folio, Executive, and custom sizes.

The document does not describe the process how to manually duplex print.

User questions

Robert C.

How to connect a printer to a wireless network using WPS-PIN?

Access the printer's Admin Menu. 2. Go to Network > WPS Setup > PIN Code. 3. Note the 8-digit PIN. 4. Start Configuration and select your wireless access point. 5. Enter the PIN into your access point within two minutes. A lit Wi-Fi LED confirms connection.

Mary N.

How to reset the camera?

To perform a factory reset, locate the reset button on the device, usually a small pinhole. Use a paperclip to press and hold the button for about 10-15 seconds until the indicator light changes, then release. The camera will then restart.

Patricia Q.

How to clean the CTD sensor?

To clean the Color Toner Density (CTD) sensor:

Open the toner access cover on the printer.
Locate the CTD sensor inside the printer.
Gently clean the CTD sensor with a soft, dry cloth. Be careful not to damage the sensor.
Close the toner access cover.

Mary N.

How to install the camera?

To install the camera, first ensure your Wi-Fi network is stable. Then, download the companion app from your app store, create an account, and follow the on-screen instructions to pair the camera. Mount the camera in your desired location using the provided mounting kit.

Mary N.

What is the purpose of the motion detection feature?

The motion detection feature allows the camera to automatically detect movement within its field of view and send instant alerts to your smartphone. Sensitivity settings and detection zones can be customized within the app.