Lighting. Ford S-MAX, Galaxy
Reklama
Reklama
Lighting
GENERAL INFORMATION
Condensation in Lamp Assemblies
Exterior lamps have vents to accommodate normal changes in air pressure.
Condensation can be a natural by-product of this design. When moist air enters the lamp assembly through the vents, there is a possibility that condensation can occur when the temperature is cold. When normal condensation occurs, a fine mist can form on the interior of the lens. The fine mist eventually clears and exits through the vents during normal operation.
Clearing time may take as long as 48 hours under dry weather conditions.
Examples of acceptable condensation are:
• The presence of a fine mist (no streaks, drip marks or large droplets).
• A fine mist covers less than 50% of the lens.
Examples of unacceptable condensation are:
• A water puddle inside the lamp.
• Streaks, drip marks or large droplets present on the interior of the lens.
If you see any unacceptable condensation, have your vehicle checked by an authorized dealer.
LIGHTING CONTROL
Lighting control positions
A
B
C
Off
Side and tail lamps
Headlamps
Parking lamps
CAUTION
Prolonged use of the parking lamps will discharge the battery.
Switch off the ignition.
Both sides
Set the lighting control to position B .
55
Galaxy/S-MAX (CA1) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 18-12-2014, CG3533en enGBR, Edition date: 11/2013, Second Printing
One side
Lighting
With all doors closed, but within the 30 second delay, opening any door will result in the three minute timer starting again.
The home safe lights can be cancelled by either pulling the direction indicator lever towards the steering wheel again or by turning the ignition switch on.
AUTOLAMPS
A
B
Right-hand side
Left-hand side
High and low beam
Pull the lever fully towards the steering wheel to switch between high and low beam.
Headlamp flasher
Pull the lever slightly towards the steering wheel.
Home safe lighting
Switch the ignition off and pull the direction indicator lever towards the steering wheel to switch the headlamps on. You will hear a short tone. The headlamps will go off automatically after three minutes with any door open, or 30 seconds after the last door has been closed.
Note: If you have switched autolamps on, you can only switch the high beam on when autolamps has switched the headlamps on.
The headlamps will come on and go off automatically depending on the ambient light.
DAYTIME RUNNING LAMPS
The lamps will illuminate when the ignition is on.
AUTOMATIC HIGH BEAM
CONTROL
WARNINGS
The system does not relieve you of your responsibility to drive with due care and attention. A manual override may be necessary if the system fails to switch the main beam on or off.
56
Galaxy/S-MAX (CA1) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 18-12-2014, CG3533en enGBR, Edition date: 11/2013, Second Printing
Lighting
WARNINGS
A manual override may be required when approaching other road users such as cyclists.
Do not use the system in fog.
CAUTIONS
In cold and severe weather conditions the system may not function. A manual override may be necessary in these cases.
Reflective road signs may be detected as oncoming traffic and the headlamps may be switched to low beam.
If the lights of oncoming vehicles are hidden by obstacles (for example guard rails) the system may not deactivate the high beam.
Always fit Ford Original Parts when replacing headlamp bulbs. Other bulbs may reduce system performance.
Check and replace wiper blades regularly to ensure the camera sensor has a clear view through the windscreen. Replacement wiper blades must be the correct length.
Note: Keep the windscreen free from obstructions such as bird droppings, insects and snow or ice.
The system will automatically switch on main beam if it is dark enough and no other traffic is present. If it detects an approaching vehicle’s headlamps or tail lamps, or street lighting ahead the system will switch off main beam before it can distract other road users. Dipped beams will remain on.
A camera sensor is centrally mounted behind the windshield of the vehicle, and monitors conditions continuously to decide when to switch the high beam off and on.
Once the system is active the high beam will switch on if:
• It is dark enough to require the use of high beams and
• there is no traffic or street lighting ahead and
• vehicle speed is greater than 40 km/h
(25 mph).
The high beam will switch off if:
• The ambient light is high enough that high beam is not required.
• An approaching vehicle's headlamps or tail lamps are detected.
• Street lighting is detected.
• Vehicle speed falls below 25 km/h (16 mph).
• The camera sensor is too hot or becomes blocked.
Activating the system
Switch on the system using the information
display and autolamps. See Information
Turn the switch to the autolamps position.
57
Galaxy/S-MAX (CA1) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 18-12-2014, CG3533en enGBR, Edition date: 11/2013, Second Printing
Lighting
Note: The system may take a short time to initialize after first switching the ignition on, especially in very dark conditions. The high beam will not automatically switch on during this period.
Setting the system sensitivity
The system has three sensitivity levels which can be accessed via the information
display. See Information Displays (page
The sensitivity determines the speed at which the high beam will be restored after detected traffic leaves the field of view.
Manually overriding the system
FRONT FOG LAMPS
WARNING
Only use the front fog lamps when visibility is considerably restricted by fog, snow or rain.
REAR FOG LAMPS
Use the high beam lever to switch between high beam and low beam.
Note: This is a temporary override and the system will return to automatic operation after a short period.
To permanently deactivate the system use the information display menu or turn the lighting control switch from autolamps to headlamps.
Note: Only use the rear fog lamps when visibility is restricted to less than 50 meters
(164 feet).
Note: Do not use the rear fog lamps when it is raining or snowing and visibility is more than 50 meters (164 feet).
HEADLAMP LEVELING
Note: Vehicles with Xenon headlamps are equipped with automatic headlamp leveling.
58
Galaxy/S-MAX (CA1) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 18-12-2014, CG3533en enGBR, Edition date: 11/2013, Second Printing
Lighting
A
B
Raised headlamp beams
Lowered headlamp beams
You can adjust the level of the headlamp beams according to the vehicle load.
Recommended headlamp leveling switch positions
Front seats
1-2
1-2
1-2
Load
Second row seats
-
-
3
Third row seats
Load in luggage compartment
Switch position
-
2
-
1-2 3 -
1 -
*
See Vehicle Identification Plate (page 265).
**
Vehicles with active suspension.
-
-
-
Max
Max
*
*
0
0 (0.5)
1 (0.5)
3 (0.5)
4 (1.5)
**
**
**
**
59
Galaxy/S-MAX (CA1) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 18-12-2014, CG3533en enGBR, Edition date: 11/2013, Second Printing
ADAPTIVE HEADLAMPS
Lighting
A
B without AFS with AFS
The AFS adjusts the headlamp low beam depending on vehicle direction and speed.
It improves visibility when you are driving at night and helps to reduce headlamp glare for oncoming drivers.
The system will not operate when the vehicle is stationary, when you have switched on the daytime running lamps or when you have selected reverse gear.
A message will appear in the information
display if the system malfunctions. See
Information Messages (page 102). The
headlamps will move to a fixed central or low beam position. Have the system checked as soon as possible.
60
Galaxy/S-MAX (CA1) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 18-12-2014, CG3533en enGBR, Edition date: 11/2013, Second Printing
Cornering lamps
Lighting
A
B
Headlamp beam
Cornering lamp beam
The cornering lamps illuminate the inside of a corner when you are turning.
DIRECTION INDICATORS
Note: Tap the lever up or down to make the direction indicators flash only three times.
61
Galaxy/S-MAX (CA1) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 18-12-2014, CG3533en enGBR, Edition date: 11/2013, Second Printing
INTERIOR LAMPS
Courtesy lamp
Lighting
Reading lamps
A
B
C
Off
Door contact
On
If you set the switch to position B , the courtesy lamp will come on when you unlock or open a door or the luggage compartment lid. If you leave a door open with the ignition switch off, the courtesy lamp will go off automatically after some time to prevent the vehicle battery from discharging. To switch it back on, switch on the ignition for a short time.
The courtesy lamp will also come on when you switch off the ignition. It will go off automatically after a short time or when you start or restart the engine.
If you set the switch to position C with the ignition switch off, the courtesy lamp will come on. It will go off automatically after a short time to prevent the vehicle battery from discharging. To switch it back on, switch on the ignition for a short time.
If you switch off the ignition, the reading lamps will go off automatically after some time to prevent the vehicle battery from discharging. To switch them back on, switch on the ignition for a short time.
LED Interior lighting
Note: Individual lamps may be switched on independently, but not off if all lamps have been switched on by the driver.
Note: All other lamps will be either non-switchable or with individual reading or dome lamp functionality only.
The lamps will come on when you unlock or open a door or the luggage compartment lid. If you leave a door open with the ignition switch off, all lamps will go off automatically after some time to prevent the vehicle battery from discharging. To switch them back on, switch on the ignition for a short time.
62
Galaxy/S-MAX (CA1) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 18-12-2014, CG3533en enGBR, Edition date: 11/2013, Second Printing
Side mounted lamp
Lighting
Center mounted lamp
A
B
C
Reading lamp on and off switch
Door function switch
All lamps on and off switch
If you press switch B all lamps remain off when the door is opened. Press the switch again to reverse.
You can control all lamps using switch C .
A
B
C
D
Right-hand side reading lamp on and off switch
Left-hand side reading lamp on and off switch
Door function switch
All lamps on and off switch
If you press switch C all lamps remain off when the door is opened. Press the switch again to reverse.
You can control all lamps using switch D .
63
Galaxy/S-MAX (CA1) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 18-12-2014, CG3533en enGBR, Edition date: 11/2013, Second Printing
Vanity mirror lamps
Lighting
1.
Open the hood. See Opening and
A
B
Off
On
If you switch off the ignition, the vanity mirror lamps will go off automatically after a short time to prevent the vehicle battery from discharging. To switch them back on, switch on the ignition for a short time.
ADJUSTING THE HEADLAMPS
To adjust the headlamps for driving on the left or right hand side of the road, see your dealer.
HAZARD WARNING FLASHERS
Note: When you remove the headlamp, make sure that the front screw remains in the headlamp molding.
2. Remove the screws.
For item location: See At a Glance (page
REMOVING A HEADLAMP
WARNING
Have Xenon bulbs changed by a properly trained technician. There is a risk of electric shock.
3. Disconnect the electrical connector.
4. Pull the headlamp as far as possible towards the center of the vehicle and disengage it from the lower fixing point.
5. Lift the outer side of the headlamp and remove it.
64
Galaxy/S-MAX (CA1) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 18-12-2014, CG3533en enGBR, Edition date: 11/2013, Second Printing
Lighting
Note: When fitting the headlamp, make sure that you reconnect the electrical connector properly.
Note: When fitting the headlamp, make sure that you fully engage the headlamp in the lower fixing point.
Note: When fitting the headlamp, make sure that the front screw is located in the headlamp molding before you install it.
Note: When fitting the headlamp, tighten the front screw first and then the rear screw.
CHANGING A BULB
WARNINGS
Switch the lights and the ignition off.
Let the bulb cool down before removing it.
Have Xenon bulbs changed by a properly trained technician. There is a risk of electric shock.
CAUTIONS
Do not touch the glass of the bulb.
Only fit bulbs of the correct
Specification Chart (page 73).
Note: The following instructions describe how to remove the bulbs. Fit replacements in the reverse order unless otherwise stated.
Headlamp
Note: Remove the covers to gain access to the bulbs.
C
D
A
B
Direction indicator
Headlamp main beam
Headlamp dipped beam
Cornering lamp
Direction indicator
1.
Removing a Headlamp (page 64).
2. Turn the bulb holder anti-clockwise and remove it.
3. Gently press the bulb into the bulb holder, turn it anti-clockwise and remove it.
65
Galaxy/S-MAX (CA1) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 18-12-2014, CG3533en enGBR, Edition date: 11/2013, Second Printing
Lighting
Headlamp main beam
1.
Removing a Headlamp (page 64).
2. Disconnect the electrical connector.
3. Release the clip and remove the bulb.
Headlamp dipped beam
1.
Removing a Headlamp (page 64).
2. Disconnect the electrical connector.
3. Release the clip and remove the bulb.
Daytime running lamps
Note: These are not serviceable items, please consult your dealer if they fail.
2. Turn the bulb holder anti-clockwise and remove it.
3. Remove the bulb.
Cornering lamp
1.
Removing a Headlamp (page 64).
66
Galaxy/S-MAX (CA1) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 18-12-2014, CG3533en enGBR, Edition date: 11/2013, Second Printing
Side repeater
Lighting
1.
Carefully remove the side repeater.
1.
Insert a screwdriver into the gap between the mirror housing and the mirror glass and release the metal retaining clip.
2. Remove the bulb holder.
3. Remove the bulb.
Approach lamp
Note: Position the mirror glass as far inwards as possible.
2. Remove the lamp.
3. Remove the bulb.
Front fog lamp and side lamp (S-
MAX)
1.
Remove the headlamp to access the
67
Galaxy/S-MAX (CA1) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 18-12-2014, CG3533en enGBR, Edition date: 11/2013, Second Printing
Lighting
Front fog lamp and side lamp
(Galaxy)
2. Disconnect the electrical connector.
Note: You cannot separate the fog lamp bulb from the bulb holder.
3. Turn the fog lamp bulb holder anti-clockwise and remove it.
4. Disconnect the electrical connector.
5. Turn the side lamp bulb holder anti-clockwise and remove it.
6. Remove the side lamp bulb.
1.
Remove the screw.
2. Remove the lamp.
3. Disconnect the fog lamp electrical connector.
Note: You cannot separate the fog lamp bulb from the bulb holder.
4. Turn the fog lamp bulb holder anti-clockwise and remove it.
68
5. Turn the side lamp bulb holder anti-clockwise and remove it.
6. Remove the side lamp bulb.
Galaxy/S-MAX (CA1) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 18-12-2014, CG3533en enGBR, Edition date: 11/2013, Second Printing
Lighting
Rear lamps (S-MAX)
Direction indicator, tail and brake lamp
Note: These are not serviceable items, please consult your dealer if they fail.
2. Remove the wing nuts.
3. Remove the lamp.
4. Disconnect the electrical connector.
Reversing lamp, tail lamp and fog lamp
5. Remove the screws.
6. Remove the bulb holder.
7.
Gently press the bulb into the bulb holder, turn it anti-clockwise and remove it.
1.
Remove the trim panel.
69
Galaxy/S-MAX (CA1) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 18-12-2014, CG3533en enGBR, Edition date: 11/2013, Second Printing
Lighting
Rear lamp (Galaxy)
Direction indicator, tail and brake lamp
1.
Remove the trim panel.
3. Remove the lamp.
4. Disconnect the electrical connector.
2. Remove the wing nuts.
Note: On some vehicles the tail lamps are
LED. These are not serviceable items, please consult your dealer if they fail.
5. Remove the screw.
6. Remove the bulb holder.
7.
Gently press the bulb into the bulb holder, turn it anti-clockwise and remove it.
70
Galaxy/S-MAX (CA1) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 18-12-2014, CG3533en enGBR, Edition date: 11/2013, Second Printing
Lighting
Reversing lamp, tail lamp and fog lamp 6. Remove the bulb holder.
7.
Gently press the bulb into the bulb holder, turn it anti-clockwise and remove it.
Central high mounted brake lamp
Note: These are not serviceable items, please consult your dealer if they fail.
Number plate lamp
1.
Remove the trim panel.
2. Remove the wing nuts.
3. Remove the lamp.
4. Disconnect the electrical connector.
1.
Carefully release the spring clip.
2. Remove the lamp.
3. Turn the bulb anti-clockwise and remove it.
Interior lamps
Vehicles with LED lamps
Note: These are not serviceable items, please consult your dealer if they fail.
5. Remove the screw.
71
Galaxy/S-MAX (CA1) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 18-12-2014, CG3533en enGBR, Edition date: 11/2013, Second Printing
Vehicles without interior sensors
Lighting
Reading lamps
Vehicles without interior sensors
1.
Carefully prise out the lens.
2. Remove the lens.
3. Remove the bulb.
Vehicles with interior sensors
1.
Carefully prise out the lens.
2. Remove the lens.
3. Remove the bulb.
Vehicles with interior sensors
1.
Carefully prise out the lens.
2. Remove the lens.
3. Remove the bulb.
1.
Carefully prise out the lamp.
2. Turn the bulb holder anti-clockwise and remove it.
72
Galaxy/S-MAX (CA1) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 18-12-2014, CG3533en enGBR, Edition date: 11/2013, Second Printing
Lighting
1.
Carefully prise out the lamp.
2. Remove the bulb.
Luggage compartment lamp and tailgate lamp
3. Remove the bulb.
Vanity mirror lamp
1.
Carefully prise out the lamp.
2. Remove the bulb.
BULB SPECIFICATION CHART
Lamp
Front direction indicator
Headlamp main beam
Headlamp dipped beam
Cornering lamp
Side repeater
Approach lamp
Front fog lamp (S-MAX)
Front fog lamp (Galaxy)
Specification
PY21W
H1
H7
H1
W5W
W5W
H8
HB4
73
Galaxy/S-MAX (CA1) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 18-12-2014, CG3533en enGBR, Edition date: 11/2013, Second Printing
Power (watt)
21
55
55
55
5
5
35
55
Lamp
Side lamp
Rear direction indicator
Rear fog lamp
Reversing lamp
License plate lamp
Interior lamp
Reading lamp
Vanity mirror lamp
Luggage compartment lamp
Lighting
Specification
W5W
PY21W
P21W
P21W
W5W
Festoon
BA9s
W5W
W6W
Power (watt)
5
21
21
21
5
10
5
5
6
74
Galaxy/S-MAX (CA1) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 18-12-2014, CG3533en enGBR, Edition date: 11/2013, Second Printing
Stáhnout
Veřejný odkaz aktualizován
Veřejný odkaz na váš chat byl aktualizován. You may view and manage your chat links after registration here.
Veřejný odkaz na dokument
Reklama
