Windows and Mirrors. Ford S-MAX, Galaxy

PDF

Dokumentti

Mainos

Windows and Mirrors

POWER WINDOWS

WARNING

Do not operate the power windows unless they are free from obstruction.

Note: If you operate the switches often during a short period of time, the system might become inoperable for a certain time to prevent damage due to overheating.

Note: You can operate the windows for several minutes after you switch off the ignition. They will be deactivated as soon as a door is opened.

Note: If you operate both the switch on the relevant door and the switch for that window on the driver’s door at the same time, the window will stop moving.

Switch on the ignition to operate the power windows.

Global opening and global closing

You can also operate the power windows with the ignition off via the global opening

and global closing function. See Global

Opening and Closing (page 42).

Note: Global opening and global closing will open or close the windows automatically only on vehicles equipped with four power windows.

Note: Global closing will only operate if you have set the memory correctly for each window.

Driver’s door switches

You can operate all the windows with the switches on the door trim panel of the driver’s door.

Front and rear passengers’ door switches

Opening and closing the windows automatically

Press or lift the switch to the second action point and release it. Press or lift it again to stop the windows.

Galaxy/S-MAX (CA1) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 18-12-2014, CG3533en enGBR, Edition date: 11/2013, Second Printing

Windows and Mirrors

Safety switch for rear windows

WARNING

On some vehicles, pressing the switch will also lock the rear doors

from inside. See Child Safety

Locks (page 27).

Note: You can always operate the rear windows from the driver’s door.

A switch in the driver’s door disables the rear power window switches.

The light in the switch illuminates and the lights in the rear window switches go off when the rear windows are disabled.

Anti-trap function

WARNING

Careless closing of the windows can override the protection function and cause injuries.

The power windows will stop automatically while closing and reverse some distance if there is an obstacle in the way.

Overriding the anti-trap function

CAUTION

While you close the window for the third time, the anti-trap function is disabled. Make sure there are no obstacles in the way of the closing window.

To override this protection function when there is a resistance, for example, in the winter, proceed as follows:

Close the window twice until it reaches the resistance and let it reverse.

2. Close the window a third time to the resistance. The anti-trap function is disabled and you cannot close the window automatically. The window will override the resistance and you can close it fully.

3. If the window does not close after the third attempt, have it checked by a properly trained technician.

Resetting the memory of the power windows

WARNING

The anti-trap function is deactivated until you have reset the memory.

After the battery has been disconnected from the vehicle you must reset the memory separately for each window:

Lift the switch until the window is fully closed. Hold the switch lifted for one more second.

2. Release the switch and lift it again, two or three times, for one more second.

3. Open the window and try to close it automatically.

4. Reset and repeat procedure if the window does not close automatically.

Galaxy/S-MAX (CA1) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 18-12-2014, CG3533en enGBR, Edition date: 11/2013, Second Printing

Windows and Mirrors

Safety mode

WARNING

The anti-trap function is not active during this procedure.

If the system detects a malfunction, it enters a safety mode. The windows will move for only about 0.5 seconds at a time and then stop again. Close the windows by pressing the switch again when the windows stop moving. Have this checked immediately.

EXTERIOR MIRRORS

WARNING

Do not overestimate the distance of the objects that you see in the convex mirror. Objects seen in convex mirrors will appear smaller and further away than they actually are.

Manual folding mirrors

Folding

Push the mirror towards the door window glass.

Unfolding

Make sure that you fully engage the mirror in its support when returning it to its original position.

POWER EXTERIOR MIRRORS

Left-hand mirror

Off

Right-hand mirror

Mirror tilting positions

The power exterior mirrors are fitted with a heating element that will defrost or

demist the mirror glass. See Heated

Windows and Mirrors (page 120).

Power folding mirrors

Automatic folding and unfolding

Note: If the mirrors have been folded using the manual fold button they can only be unfolded using the manual fold button.

Galaxy/S-MAX (CA1) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 18-12-2014, CG3533en enGBR, Edition date: 11/2013, Second Printing

Windows and Mirrors

The mirrors will fold automatically when you lock the vehicle with the key, the remote control or a keyless entry system request. The mirrors will unfold when you unlock the vehicle with the key, the remote control, a keyless entry system request, the driver's interior door handle or starting the engine.

Manual folding and unfolding

The power folding mirrors operate with the ignition on.

Note: You can operate the mirrors (mirror tilting and folding) for several minutes after you switch off the ignition. They will be deactivated as soon as a door is opened.

Press the button to fold or unfold the mirrors.

If you press the switch again while the mirrors are moving, they will stop and reverse the direction of movement.

Note: When the mirrors are operated often during a short period of time, the system may become inoperable for a period of time to prevent damage due to overheating.

Reverse mirror dipping

Depending on the switch position ( A or C ), the relevant exterior mirror will dip whenever you select reverse gear, giving you a view of the curb.

Note: You can disable this feature by leaving the switch in position B .

The exterior mirror will return to the original position:

• If the vehicle speed exceeds 10 km/h

(6 mph).

• Approximately 10 seconds after reverse gear has been disengaged.

• If the switch is returned to position B .

When you first use this feature, the mirror will dip to a preset position. This position can be adjusted using the following sequence:

Turn the ignition on. Do not start the engine.

2. Select the desired exterior mirror ( A or

C ).

3. Select reverse gear, the selected exterior mirror will adjust to a preset position.

4. Adjust the mirror to the required dipped position.

5. Disengage reverse gear or press and hold the desired memory pre-set button until a single chime sounds to

confirm. See Memory Function (page

142).

The settings will be stored automatically.

Galaxy/S-MAX (CA1) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 18-12-2014, CG3533en enGBR, Edition date: 11/2013, Second Printing

Windows and Mirrors

AUTO-DIMMING MIRROR

The auto-dimming mirror will adjust automatically when hit by glaring light from behind. It will not work when you have selected reverse gear.

REAR QUARTER WINDOWS

Manual rear quarter windows

Opening

Closing

Galaxy/S-MAX (CA1) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 18-12-2014, CG3533en enGBR, Edition date: 11/2013, Second Printing

Windows and Mirrors

Note: Make sure that the lever is securely engaged in its catch.

Power rear quarter windows

Switch on the ignition to operate the rear quarter windows.

BLIND SPOT INFORMATION

SYSTEM

Blind spot information system

(BLIS)

WARNINGS

The system is not designed to prevent contact with other vehicles or objects. The system only provides a warning to assist you in detecting vehicles in the blind spot zones. The system will not detect obstacles, pedestrians, motorcyclists or cyclists.

Do not use the system as a replacement for using the side and rear view mirrors, and looking over your shoulder before changing lanes. The system is not a replacement for careful driving and is only to be used as an aid.

The system is a convenience feature that aids the driver in detecting vehicles that may have entered the blind spot zone ( A ).

The detection area is on both sides of the vehicle extending rearwards from the exterior mirrors to approximately 3 meters

(10 feet) beyond the bumper. The system will alert you if certain vehicles enter the blind spot zone whilst driving.

Galaxy/S-MAX (CA1) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 18-12-2014, CG3533en enGBR, Edition date: 11/2013, Second Printing

Windows and Mirrors

Using the system

The system displays a yellow indicator located in the exterior mirrors.

Note: Both indicators will illuminate briefly when you switch the ignition on to confirm that the system is operational.

Note: On vehicles with automatic transmission, the system is active only in S,

D and N .

The system is only active when you exceed

10 km/h (6 mph). The system is temporarily deactivated when you select reverse gear.

System detection and alerts

The system will trigger the alert for vehicles that enter the blind spot zone from the rear or merge from the side. Vehicles that you pass, or vehicles that enter the blind spot zone from the front, will only trigger the alert after the vehicle has remained in the blind spot zone for a short period of time.

Note: Vehicles that pass through the blind zone quickly (typically less than 2 seconds) will not trigger the alert.

The system consists of two radar sensors each located behind the rear wheels hidden behind the bumpers.

CAUTIONS

Do not place items such as bumper stickers in this area.

Repairs to these areas using body filler will affect the performance of the system.

Detection limitations

There may be certain instances where vehicles entering and exiting the blind spot zones may not be detected.

Instances which may cause non-detection:

• Debris build up on the rear bumper panels in the area of the sensors.

• Certain manoeuvring of vehicles entering and exiting the blind zone.

• Vehicles passing through the blind zone at high speed.

• Severe weather conditions.

• Several vehicles passing through the blind zone following each other closely.

False alerts

Note: False alerts are temporary and will self correct.

There may be certain instances when the system will alert with no vehicle present in the blind zone.

Circumstances where false alerts may occur:

• Road guardrails.

• Highway concrete walls.

• Construction areas.

• Sharp turns around a building.

• Bushes and trees.

Galaxy/S-MAX (CA1) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 18-12-2014, CG3533en enGBR, Edition date: 11/2013, Second Printing

Windows and Mirrors

• Cyclists and motorcyclists.

• Coming to a stop with a vehicle directly behind but very close.

Turning the system on and off

Note: The on or off position will remain until manually changed.

You can turn the system on and off using

the information display. See Information

Displays (page 89).

When you turn the system off no further alerts will be received. The BLIS warning

indicator will illuminate. See Warning

Lamps and Indicators (page 85).

Detection errors

Note: The alert indicator in the mirror will not illuminate.

If the system senses a fault on either sensor, the system warning symbol will illuminate and remain on. The information display will confirm the fault and indicate whether the left or right side is affected.

Blocked sensor

WARNING

Prior to the system recognizing a blocked condition and issuing a warning, the number of missed objects will increase.

CAUTION

The sensors may not detect vehicles in heavy rain or other conditions that cause disruptive reflections.

Note: Keep the rear bumper area surrounding the sensors free from dirt, ice and snow.

If a sensor becomes blocked the system performance may degrade. A blocked sensor message may be displayed.

The system will automatically return to normal operation once two other vehicles have been detected on both sides.

Trailer towing false alerts

CAUTION

Vehicles fitted with a trailer tow module not approved by us may not correctly be detected. Switch the

system off to avoid false alerts. See