Telephone
GENERAL INFORMATION
CAUTION
Using the system with the engine off will drain the battery.
This section describes the functions and features of the Bluetooth cell phone hands free system.
The Bluetooth cell phone part of the system provides interaction with the audio or navigation system and your cell phone.
It allows you to use the audio or navigation system to make and receive calls without having to hold your cell phone.
Compatibility of phones
CAUTION
As no common agreement exists, cell phone manufacturers are able to implement a variety of profiles in their
Bluetooth devices. Because of this, an incompatibility can occur between the phone and hands-free system, which in some cases may significantly degrade the system performance. To avoid this situation, only recommended phones should be used.
Please visit the website www.fordmobile-connectivity.com
for full details.
BLUETOOTH SETUP
Before you can use your telephone with your vehicle it must be bonded to the vehicle telephone system.
Handling of phones
Up to six Bluetooth devices can be bonded to the vehicle system.
Note: If there is an ongoing call when the phone in use is selected as the new active phone, the call is transferred to the vehicle audio system.
Note: Even if connected to the car system, your phone can still be used in the usual way.
Requirements for Bluetooth connection
The following are required before a
Bluetooth phone connection can be made.
1.
The Bluetooth feature must be activated on the phone and on the audio unit. Make sure the Bluetooth menu option in the audio unit is set to
ON . For information on phone settings, refer to your phone user guide.
2. In the Bluetooth menu on your phone, search for Ford Audio and select it.
3. Enter the code number shown on the vehicle display using the phone keypad.
If no code number is shown on the display, enter the Bluetooth PIN number 0000 using the phone keypad.
Now enter the Bluetooth PIN number shown on the vehicle display.
4. If your cell phone asks you to authorize the automatic connection, select YES .
Note: A phone call will be disconnected if the audio unit is switched off. If the ignition key is turned to the off position the phone call will remain in progress.
TELEPHONE SETUP
Phonebook
After start up access to the phonebook list can be delayed for several minutes, depending upon the size.
293
Galaxy/S-MAX (CA1) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 18-12-2014, CG3533en enGBR, Edition date: 11/2013, Second Printing
Telephone
Phonebook categories
Depending on your phonebook entry, different categories can be displayed in the audio unit.
For example:
M
O
H
F
Mobile
Office
Home
Fax
Note: Entries may be displayed without a category attachment.
The category can also be indicated as an icon:
Phone
Mobile
Home
Office
Fax
Select the phone from the active phone menu.
Turning the ignition and radio or navigation unit back on again, the last active phone is picked up by the system.
Note: In some cases the Bluetooth connection must also be confirmed on the phone.
Bond another Bluetooth phone
Bond a new Bluetooth phone as described in the requirements for a Bluetooth connection.
Phones stored in the system are accessible by using the phone list on the audio unit.
Note: A maximum of six devices may be bonded. If six Bluetooth devices have already been bonded, one of these has to be debonded in order to bond a new device.
TELEPHONE CONTROLS
Remote control
Voice, accept and reject button
Making a phone an active phone
When using the system for the first time, no phone is connected to the system.
Bluetooth phone
After bonding a Bluetooth phone to the system, this becomes the active phone.
For further information refer to the phone menu.
1
2
Voice button
Accept and reject button
The VOICE button is used to activate or switch off the voice control.
On vehicles with an accept and reject button, phone calls can be accepted and rejected by pressing the appropriate button.
294
Galaxy/S-MAX (CA1) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 18-12-2014, CG3533en enGBR, Edition date: 11/2013, Second Printing
Telephone
Note: Some audio units have the accept and reject buttons on the front bezel. These operate in the same way.
USING THE TELEPHONE
This chapter describes the phone functions of the audio unit.
Note: Refer to your audio guide for details of the controls.
An active phone must be present.
Even if connected to the audio unit, your phone can still be used in the usual way.
Note: You can exit the phone menu by pressing any source button CD , AM/FM or
AUX .
Making a call
Dialing a number using voice control
Phone numbers can be dialed using voice
control. See Telephone commands
(page 309).
Dialing a number using the address book
You can access your phone address book via Bluetooth. The entries will appear in the unit display.
1.
Press the PHONE or the call accept button.
2. Press the MENU button.
3. Keep pressing the MENU button until
PHONEBOOK appears.
4. Press the seek buttons to select the desired phone number.
Note: Press and hold the seek button to skip to the next letter in the alphabet.
5. Press the PHONE or the call accept button to dial the selected phone number.
Dialing a number using the address book - Sony radio
You can access your phone address book via Bluetooth. The entries will appear in the unit display.
1.
Press the PHONE button.
2. Press the seek button until the phone book is shown.
3. Press the up/down arrow buttons to select the desired phone number.
Note: Press and hold the up/down arrow buttons to skip to the next letter in the alphabet.
4. Press the PHONE or the call accept button to dial the selected phone number.
Dialing a number using the telephone keypad
If you have an audio unit with a telephone keypad (buttons 0-9, * and #):
1.
Press the call accept button. Press the
PHONE button if you have a Sony radio.
2. Dial the number using the telephone keypad on the audio unit.
3. Press the call accept button.
Note: If you enter an incorrect digit whilst entering a phone number, press the seek left button to erase the last digit. A long press will erase the complete string of digits.
Press and hold 0 to enter a + digit.
Ending a call
Calls can be ended by pressing the call reject button.
Audio units without a telephone keypad can also end a call by pressing either
PHONE , CD , AM/FM or ON/OFF , or by pressing the MODE button on the remote control
295
Galaxy/S-MAX (CA1) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 18-12-2014, CG3533en enGBR, Edition date: 11/2013, Second Printing
Telephone
Redialing a number
1.
Press the PHONE or the call accept button.
2. Press the MENU button.
3. Select the CALL OUT list or the CALL
IN list. On some audio units, select the
MISSED , INCOMING or OUTGOING calls list.
Note: If the active phone does not provide a call out list, the last outgoing call number/entry can be redialed.
4. Press the seek button on the audio unit.
5. Press the PHONE or the call accept button to dial the desired phone number.
Redialing a number - Sony radio
1.
Press the PHONE or the call accept button.
2. Press the seek button until the desired list is displayed.
Note: If the active phone does not provide a call out list, the last outgoing call number/entry can be redialed.
3. Press the up/down buttons to select the desired phone number.
4. Press the PHONE or the call accept button to dial the phone number.
Redialing the last dialed number - Sony radio
1.
Press the call accept button.
2. Press the call accept button a second time to dial the number.
Receiving an incoming call
Accepting an incoming call
Incoming calls can be accepted by pressing either the call accept button, the PHONE button or the MODE button on the remote control.
Rejecting an incoming call
Incoming calls can be rejected by pressing the call reject button.
Audio units without a telephone keypad can also reject a call by pressing either
PHONE , CD , AM/FM or ON/OFF .
Receiving a second incoming call
Note: The second incoming call function must be activated in your phone.
If there is an incoming call whilst there is an ongoing call, a beep will be heard and you will have the option to end the active call and to accept the incoming call.
Accepting a second incoming call
Second incoming calls can be accepted by pressing either the call accept button, the PHONE button, or the MODE button on the remote control.
Rejecting a second incoming call
Second incoming calls can be rejected by pressing the call reject button. Units without a telephone keypad can also reject a second incoming call by pressing the CD button, or the AM/FM button.
Muting the microphone
During a call, it is possible to mute the microphone. Whilst muted, confirmation will appear in the display.
Audio units with green call accept button
Press the call accept button. Press the button once again to turn this function off.
Audio units without green call accept button
Press the seek up or down button. Press the button once again to turn this function off.
296
Galaxy/S-MAX (CA1) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 18-12-2014, CG3533en enGBR, Edition date: 11/2013, Second Printing
Telephone
Changing the active phone
Note: Phones must be bonded to the system before they can be made active.
Using the station storage button
Note: This process is only for audio units without a telephone keypad.
1.
Press the PHONE button on the audio unit.
2. Press the preset number required
(using the station preset buttons 1 - 6).
Using the audio unit menu
Note: After bonding a phone to the system, this becomes the active phone.
1.
Press the PHONE or call accept button.
2. Press the MENU button on the audio unit.
3. Select the ACTIVE PHONE option on the audio unit.
4. Scroll through the different stored phones by using the seek buttons to display the bonded phones.
5. Press the MENU button to select the phone which is to be the active phone.
Debonding a bonded phone
A bonded phone can be deleted from the system at any time, unless a phone call is in progress.
1.
Press the PHONE or call accept button.
2. Press the MENU button on the audio unit.
3. Select the DEBOND option on the audio unit.
4. Scroll through the different phones by using the seek buttons and display the phone to be debonded.
5. Press the MENU button to select the phone which is to be debonded.
Debonding a bonded phone - Sony radio
A bonded phone can be deleted from the system at any time, unless a phone call is in progress.
1.
Press the PHONE button.
2. Press the up/down arrow buttons until you reach the DEBOND option.
3. Scroll through the different phones by using the seek buttons and display the phone to be debonded.
4. Press the OK button to be debond.
USING THE TELEPHONE
This chapter describes the phone functions of the Navigation System.
Note: Refer to your Navigation System guide for details of the controls.
An active phone must be present.
Even if connected to the navigation system, your phone can still be used in the usual way.
Making a call
Dialing a number
Phone numbers can be dialed using voice
control. See Voice control (page 299).
Ending a call
Calls can be ended by pressing either the
END button, the MODE button on the remote switch or the ON/OFF button on the navigation system.
Redialing a number
1.
Press the PHONE button on the unit.
2. Select REDIAL .
297
Galaxy/S-MAX (CA1) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 18-12-2014, CG3533en enGBR, Edition date: 11/2013, Second Printing
Telephone
Receiving an incoming call
Accepting an incoming call
Incoming calls can be accepted by pressing either the call accept button, the MODE button on the remote control, the PHONE button on the unit or by using the ACCEPT option in the menu.
Rejecting an incoming call
Incoming calls can be rejected by pressing either the call reject button, the CD or
AM/FM buttons on the unit, or by using the REJECT option in the menu.
Receiving a second incoming call
Note: The second incoming call function must be activated in your phone.
If there is an incoming call, whilst there is an ongoing call, a beep will be heard and you will have the option to end the active call and to accept the incoming call.
Accepting a second incoming call
Second incoming calls can be accepted by pressing either the call accept button, the MODE button on the remote control, the PHONE button on the unit or by using the ACCEPT option in the menu.
Note: This will cancel the ongoing call.
Rejecting a second incoming call
Second incoming calls can be rejected by pressing either the call reject button, or one of the following buttons on the unit: CD,
AM/FM .
Muting the microphone
During a call, it is possible to mute the microphone. Whilst muted, confirmation will appear in the display.
SD navigation units
Press the mute button (symbol of a microphone with a line through it). Press the button once again to turn this function off.
CD navigation units
Press the microphone mute button. Press the button once again to turn this function off.
Changing the active phone
Note: Phones must be bonded to the system before they can be made active.
Note: After bonding a phone to the system, this becomes the active phone.
1.
Press the PHONE button on the unit.
2. Using the BT SETTINGS option in the menu, select the active phone from the list.
Debonding a bonded phone
A bonded phone can be deleted from the system at any time, unless a phone call is in progress.
1.
Press the PHONE button on the unit.
2. Select the BT SETTINGS option in the menu.
3. Select the DEBOND option in the menu.
4. Select the phone from the list.
298
Galaxy/S-MAX (CA1) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 18-12-2014, CG3533en enGBR, Edition date: 11/2013, Second Printing
