Wheels and Tires. Ford S-MAX, Galaxy
Anuncio
Anuncio
Wheels and Tires
GENERAL INFORMATION
CAUTIONS
Use only approved wheel and tire sizes. Using other sizes could damage the vehicle and will make the National
Type Approval invalid.
If you change the diameter of the tires from that fitted at the factory, the speedometer may not display the correct speed. Take the vehicle to your dealer to have the engine management system reprogrammed.
If you intend to change the size of the wheels from that fitted at the factory, check the suitability with your dealer.
Note: Check your tire pressures regularly to optimize fuel economy.
A decal with tire pressure data is located in the driver’s door opening at the B-pillar.
Check and set the tire pressure at the ambient temperature in which you are intending to drive the vehicle and when the tires are cold.
TEMPORARY MOBILITY KIT
Your vehicle is not equipped with a spare tire, but does include an emergency tire repair kit that can be used to repair one flat tire.
The tire repair kit is located in the
underfloor storage compartment. See
Storage compartments (page 140).
Note: Remove the underfloor storage compartment screws if fitted.
General information
WARNINGS
Depending on the type and extent of tire damage, some tires can only be partially sealed or not sealed at all.
Loss of tire pressure can affect vehicle handling, leading to loss of vehicle control.
Do not use the tire repair kit if the tire has already been damaged as a result of being driven under inflated.
Do not use the tire repair kit on run flat tires.
Do not try to seal damage other than that located within the visible tread of the tire.
Do not try to seal damage to the tire sidewall.
The tire repair kit seals most tire punctures
[with a diameter of up to six millimeters
(1/4 inch)] to temporarily restore mobility.
Observe the following rules when using the kit:
• Drive with caution and avoid making sudden steering or driving maneuvres , especially if the vehicle is heavily loaded or you are towing a trailer.
• The kit will provide you with an emergency temporary repair, enabling you to continue your journey to the next vehicle or tire dealer, or to drive a maximum distance of 200 kilometers
(125 miles).
• Do not exceed a maximum speed of
80 km/h (50 mph) .
• Keep the kit out of the reach of children.
• Only use the kit when the ambient temperature is between –30°C (-22°F) and +70°C (+158°F).
253
Galaxy/S-MAX (CA1) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 18-12-2014, CG3533en enGBR, Edition date: 11/2013, Second Printing
Wheels and Tires
Using the tire repair kit
WARNINGS
Compressed air can act as an explosive or propellant.
Never leave the tire repair kit unattended while in use.
CAUTION
Do not keep the compressor operating for more than 10 minutes.
Note: Use the tire repair kit only for the vehicle with which it was supplied.
• Park your vehicle at the roadside so that you do not obstruct the flow of traffic and so that you are able to use the kit without being in danger.
• Apply the parking brake, even if you have parked on a level road, to make sure that the vehicle will not move.
• Do not attempt to remove foreign objects like nails or screws penetrating the tire.
• Leave the engine running while the kit is in use, but not if the vehicle is in an enclosed or poorly ventilated area (for example, inside a building). In these circumstances, switch the compressor on with the engine turned off.
• Replace the sealant bottle with a new one before the expiry date (see top of bottle) is reached.
• Inform all other users of the vehicle that the tire has been temporarily sealed with the tire repair kit and make them aware of the special driving conditions to be observed.
Inflating the tire
WARNINGS
Check the sidewall of the tire prior to inflation. If there are any cracks, bumps or similar damage, do not attempt to inflate the tire.
Do not stand directly beside the tire while the compressor is pumping.
Watch the sidewall of the tire. If any cracks, bumps or similar damage appear, turn off the compressor and let the air out by means of the pressure relief valve B . Do not continue driving with this tire.
The sealant contains natural rubber latex. Avoid contact with skin and clothing. If this happens, rinse the affected areas immediately with plenty of water and contact your doctor.
If the tire inflation pressure does not reach 1.8 bar (26 psi) within seven minutes, the tire may have suffered excessive damage, making a temporary repair impossible. In this case, do not continue driving with this tire.
CAUTION
Screwing the bottle onto the bottle holder will pierce the seal of the bottle. Do not unscrew the bottle from the holder as the sealant will escape.
254
Galaxy/S-MAX (CA1) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 18-12-2014, CG3533en enGBR, Edition date: 11/2013, Second Printing
E
F
C
D
G
A
B
J
K
H
I
Protective cap
Pressure relief valve
Hose
Orange cap
Bottle holder
Pressure gauge
Power plug with cable
Compressor switch
Label
Bottle lid
Sealant bottle
1.
Open the lid of the tire repair kit.
Wheels and Tires
2. Peel off the label I showing the maximum permissible speed of
80 km/h (50 mph) from the casing and attach it to the instrument panel in the driver’s field of view. Make sure the label does not obscure anything important.
3. Take the hose C and the power plug with cable G out of the kit.
4. Unscrew the orange cap D and the bottle lid J .
5. Screw the sealant bottle K clockwise into the bottle holder E fully tight.
6. Remove the valve cap from the damaged tire.
7.
Detach the protective cap A from the hose C and screw the hose C firmly onto the valve of the damaged tire.
8. Make sure that the compressor switch
H is in position 0 .
9. Insert the power plug G into the cigar
lighter socket or auxiliary power socket.
See Cigar Lighter (page 138). See
Auxiliary Power Points (page 138).
10.
Start the engine.
11.
Move the compressor switch H to position 1 .
12.
Inflate the tire for no longer than seven minutes to an inflation pressure of minimum 1.8 bar (26 psi) and a maximum of 3.5 bar (51 psi). Move the compressor switch H to position
0 and check the current tire pressure with pressure gauge F .
13.
Remove the power plug G from the cigar lighter socket or auxiliary power socket.
14.
Quickly unscrew the hose C from the tire valve and replace the protective cap A . Fasten the valve cap again.
15.
Leave the sealant bottle K in the bottle holder E .
255
Galaxy/S-MAX (CA1) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 18-12-2014, CG3533en enGBR, Edition date: 11/2013, Second Printing
Wheels and Tires
16.
Make sure the kit, the bottle lid and the orange cap are stored safely, but still easily accessible in the vehicle.
The kit will be required again when you check the tire pressure.
17.
Immediately drive approximately three kilometers (two miles) so that the sealant can seal the damaged area.
Note: When pumping in the sealant through the tire valve, the pressure may rise up to
6 bar (87 psi) but will drop again after about
30 seconds.
WARNING
If you experience heavy vibrations, unsteady steering behavior or noises while driving, reduce your speed and drive with caution to a place where it is safe for you to stop the vehicle. Recheck the tire and its pressure. If the tire pressure is less than 1.3 bar (19 psi) or if there are any cracks, bumps or similar damage visible, do not continue driving with this tire.
Checking the tire pressure
1.
Stop the vehicle after driving approximately three kilometers
(two miles). Check, and where necessary, adjust the pressure of the damaged tire.
2. Attach the kit and read the tire pressure from the pressure gauge F .
3. If the pressure of the sealant-filled tire is 1.3 bar (19 psi) or more, adjust it to
the specified pressure. See Technical
4. Follow the inflation procedure once again to top up the tire.
5. Check the tire pressure again from the pressure gauge F . If the tire pressure is too high, deflate the tire to the specified pressure using the pressure relief valve B .
6. Once you have inflated the tire to its correct tyre pressure, move the compressor switch H to position 0 , remove the power plug G from the socket, unscrew the hose C , fasten the valve cap and replace the protective cap A .
7.
Leave the sealant bottle K in the bottle holder E and store the kit away safely in its original location.
8. Drive to the nearest tire specialist to get the damaged tire replaced. Before the tire is removed from the rim, inform your tire dealer that the tire contains sealant. Renew the kit as soon as possible after it has been used once.
Note: Remember that emergency roadside tire repair kits only provide temporary mobility. Regulations concerning tire repair after usage of tire repair kit may differ from country to country. You should consult a tire specialist for advice.
WARNING
Before driving, make sure the tire is adjusted to the recommended
inflation pressure. See Technical
Specifications (page 262). Monitor the
tire pressure until the sealed tire is replaced.
Empty sealant bottles can be disposed of together with normal household waste.
Return remains of sealant to your dealer or dispose of it in compliance with local waste disposal regulations.
256
Galaxy/S-MAX (CA1) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 18-12-2014, CG3533en enGBR, Edition date: 11/2013, Second Printing
Wheels and Tires
TIRE CARE
To make sure the front and rear tires of your vehicle wear evenly and last longer, we recommend that you swap the tires from front to rear and vice versa at regular intervals of between 5000 and 10000 kilometers (3000 and 6000 miles).
CAUTION
Do not scrub the sidewalls of the tires when you are parking.
If you have to mount a curb, do so slowly and approach it with the wheels at right-angles to the curb.
Examine the tires regularly for cuts, foreign objects and uneven wear of the tread.
Uneven wear could mean that the wheel alignment is outside specification.
Check the tire pressures (including the spare) when cold, every two weeks.
USING WINTER TIRES
CAUTION
Make sure that you use the correct lug nuts for the type of wheel the winter tires are fitted to.
If winter tires are used, make sure that the
tire pressures are correct. See Technical
USING SNOW CHAINS
WARNINGS
Do not exceed 50 km/h (30 mph).
Do not use snow chains on snow-free roads.
Only fit snow chains to specified
tires. See Technical Specifications
CAUTION
If your vehicle is fitted with wheel trims, remove them before fitting snow chains.
Note: The ABS will continue to operate normally.
Only use small link snow chains.
Only use snow chains on the front wheels.
Vehicles with stability control
(ESC)
Vehicles with stability control (ESC) may exhibit some unusual driving characteristics which can be reduced by
switching traction control off. See Using
TIRE PRESSURE MONITORING
SYSTEM
WARNINGS
The system does not relieve you of your responsibility to regularly check the tire pressures.
The system will only provide a low tire pressure warning. It will not inflate the tires.
257
Galaxy/S-MAX (CA1) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 18-12-2014, CG3533en enGBR, Edition date: 11/2013, Second Printing
Wheels and Tires
WARNINGS
The system may take longer to detect low pressure in the tires if you have fitted snow chains.
Do not drive on significantly under-inflated tires. This may cause the tires to overheat and fail.
Under-inflation reduces fuel efficiency, tire tread life and may also affect your ability to drive the vehicle safely.
Do not bend or damage the valves when you are inflating the tires.
Have tires installed by properly trained technicians.
Note: After changing the tires or sensors the system will take a few minutes to reset.
During this period the system is operational but a warning lamp may appear.
Note: If you fit tires that do not have monitoring sensors, a message will be
shown in the display. See Information
Messages (page 102). Confirm this message
to deactivate the system.
The system monitors the pressure in the tires using sensors located on the wheels and a receiver located in your vehicle.
When the system detects low pressure in the tires, a warning message is displayed
in the information display. See
Information Messages (page 102).
If a low pressure warning message is displayed in the information display, check the tire pressures as soon as possible and inflate them to the recommended
pressure. See Technical Specifications
(page 262). If this happens frequently, have
the cause determined and rectified as soon as possible.
Checking the tire pressures
Note: If the tire pressures are greater than or equal to 3.3 bar (48 lbf/in²), you will see the + symbol below the pressure value. The system only measures pressure up to 3.3
bar (48 lbf/in²). The + symbol indicates that the tire pressures may be higher.
Note: Type 3 instrument clusters have a slightly different menu structure. Select
Settings first to access Information .
1.
Press the right arrow button on the steering wheel to enter the main menu.
2. Highlight Information with the up and down buttons and press the right arrow button.
3. Highlight Tire Pressures with the up and down buttons and press the right arrow button.
4. Highlight the desired setting and press the OK button to confirm the setting.
5. Press the left arrow button to exit the menu. Hold the left arrow button pressed to return to the trip computer display.
Setting the vehicle load
Note: Type 3 instrument clusters have a slightly different menu structure. Select
Settings first to access Setup .
Correct tire pressure settings depend on
Specifications (page 262). The system
can only detect low pressure if you have entered the current vehicle load.
1.
Press the right arrow button on the steering wheel to enter the main menu.
2. Highlight Setup with the up and down buttons and press the right arrow button.
3. Highlight Tyre Pressures with the up and down buttons and press the right arrow button.
258
Galaxy/S-MAX (CA1) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 18-12-2014, CG3533en enGBR, Edition date: 11/2013, Second Printing
Wheels and Tires
4. Highlight the desired setting and press the OK button to confirm the setting.
5. Press the left arrow button to exit the menu. Hold the left arrow button pressed to return to the trip computer display.
CHANGING A ROAD WHEEL
Locking lug nuts
You can obtain a replacement locking lug nut key and replacement locking lug nuts from your dealer using the reference number certificate.
Vehicle jack
Your vehicle is not equipped with a vehicle jack or a wheel brace.
It is recommended to use a workshop type hydraulic jack for changing between summer and winter tires.
Jacking and lifting points
WARNING
Never place anything between the jack and the ground, or the jack and the vehicle.
CAUTION
Use only the specified jacking points.
If you use other positions, you may damage the body, steering, suspension, engine, braking system or the fuel lines.
Note: Use a jack with a minimum lifting capacity of 1.5 tonnes and a lifting plate with a minimum diameter of 80 millimeters (3.1
inches).
Indentations in the sills A show the location of the jacking points.
259
Galaxy/S-MAX (CA1) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 18-12-2014, CG3533en enGBR, Edition date: 11/2013, Second Printing
Wheels and Tires
Vehicles with side skirts
Place the lifting plate through the cut out on the underside of the skirt.
Removing a road wheel
WARNINGS
Park your vehicle in such a position that neither the traffic nor you are hindered or endangered.
Set up a warning triangle.
Make sure that the vehicle is on firm, level ground with the wheels pointing straight ahead.
Switch off the ignition and apply the parking brake.
If your vehicle has a manual transmission, select first or reverse gear. If it has an automatic transmission, select park.
Have the passengers leave the vehicle.
Secure the diagonally opposite wheel with an appropriate block or wheel chock.
WARNINGS
Make sure that the arrows on directional tires point in the direction of rotation when the vehicle is moving forwards. If you have to fit a spare wheel with the arrows pointing in the opposite direction, have the tire refitted in the correct direction by a properly trained technician.
Do not work underneath the vehicle when it is supported only by a jack.
Make sure that the jack is vertical to the jacking point and the base is flat on the ground.
CAUTION
Do not lay alloy wheels face down on the ground, this will damage the paint.
1.
Remove the hub cap or cover.
2. Install the locking lug nut key.
3. Slacken the lug nuts.
4. Jack up the vehicle until the tire is clear of the ground.
5. Remove the lug nuts and the wheel.
260
Galaxy/S-MAX (CA1) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 18-12-2014, CG3533en enGBR, Edition date: 11/2013, Second Printing
Wheels and Tires
Installing a road wheel
WARNINGS
Use only approved wheel and tire sizes. Using other sizes could damage the vehicle and will make
the National Type Approval invalid. See
Technical Specifications (page 262).
Do not fit run flat tires on vehicles that were not originally fitted with them. Please contact your dealer for more details regarding compatibility.
CAUTION
Do not install alloy wheels using lug nuts designed for use with steel wheels.
Note: The lug nuts of alloy wheels and spoked steel wheels can also be used for the steel spare wheel for a short time
(maximum two weeks).
Note: You can use lug nuts designed for use with alloy wheels with steel wheels.
Note: Make sure the wheel and hub contact surfaces are free from foreign matter.
Note: Make sure that the cones on the lug nuts are against the wheel.
1.
Install the wheel.
2. Install the lug nuts finger tight.
3. Install the locking lug nut key.
4. Partially tighten the lug nuts in the sequence shown.
5. Lower the vehicle and remove the jack.
6. Fully tighten the lug nuts in the
7.
Install the hub cap or cover using the ball of your hand.
261
Galaxy/S-MAX (CA1) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 18-12-2014, CG3533en enGBR, Edition date: 11/2013, Second Printing
Wheels and Tires
WARNING
Have the lug nuts checked for tightness and the tire pressure checked as soon as possible.
TECHNICAL SPECIFICATIONS
Lug nut torque
Wheel type
All
Nm (Ib-ft)
170 (125)
262
Galaxy/S-MAX (CA1) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 18-12-2014, CG3533en enGBR, Edition date: 11/2013, Second Printing
Wheels and Tires
Tire pressures (cold tires)
Up to 160 km/h (100 mph)
Variant Tire size
Normal load
Front Rear bar (lbf/ in²) bar (lbf/ in²)
1.6L EcoBoost SCTi
(Sigma), 2.0L
EcoBoost SCTi
(MI4), 1.6L
Duratorq-TDCi (DV)
Diesel Stage V, 2.0L
Duratorq-TDCi
(DW) and 2.2L
Duratorq-TDCi
(DW)
215/60 R 16 *
1.6L EcoBoost SCTi
(Sigma), 2.0L
EcoBoost SCTi
(MI4), 1.6L
Duratorq-TDCi (DV)
Diesel Stage V, 2.0L
Duratorq-TDCi
(DW) and 2.2L
Duratorq-TDCi
(DW)
225/50 R 17 and
235/45 R 18
2.0L Duratec-HE
(MI4) and 2.3L
Duratec-HE (MI4)
2.0L Duratec-HE
(MI4) and 2.3L
Duratec-HE (MI4)
215/60 R 16
225/50 R 17 and
235/45 R 18
*
*
Only fit snow chains to specified tires.
2.4 (35)
2.4 (35)
2.2 (32)
2.2 (32)
2.4 (35)
2.2 (32)
2.4 (35)
2.2 (32)
Full load
Front Rear bar (lbf/ in²) bar (lbf/ in²)
2.6 (38)
2.6 (38)
2.6 (38)
2.6 (38)
3.1 (45)
3.1 (45)
3.1 (45)
3.1 (45)
263
Galaxy/S-MAX (CA1) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 18-12-2014, CG3533en enGBR, Edition date: 11/2013, Second Printing
Wheels and Tires
Continuous speed in excess of 160 km/h (100 mph)
Variant Tire size
Normal load
Front Rear bar (lbf/ in²) bar (lbf/ in²)
1.6L EcoBoost SCTi
(Sigma), 1.6L
Duratorq-TDCi (DV)
Diesel Stage V and
2.0L Duratorq-TDCi
(DW)
215/60 R 16
1.6L EcoBoost SCTi
(Sigma), 1.6L
Duratorq-TDCi (DV)
Diesel Stage V and
2.0L Duratorq-TDCi
(DW)
225/50 R 17 and
235/45 R 18
2.0L Duratec-HE
(MI4) and 2.3L
Duratec-HE (MI4)
2.0L Duratec-HE
(MI4) and 2.3L
Duratec-HE (MI4)
215/60 R 16
225/50 R 17 and
235/45 R 18
2.0L EcoBoost SCTi
(MI4) and 2.2L
Duratorq-TDCi
(DW)
215/60 R 16
2.0L EcoBoost SCTi
(MI4) and 2.2L
Duratorq-TDCi
(DW)
225/50 R 17 and
235/45 R 18
2.5 (36)
2.5 (36)
2.4 (35)
2.4 (35)
2.6 (38)
2.6 (38)
2.4 (35)
2.3 (33)
2.4 (35)
2.2 (32)
2.6 (38)
2.6 (38)
Full load
Front Rear bar (lbf/ in²) bar (lbf/ in²)
2.7 (39)
2.7 (39)
2.6 (38)
2.6 (38)
2.8 (41)
2.8 (41)
3.1 (45)
3.1 (45)
3.1 (45)
3.1 (45)
3.3 (48)
3.4 (49)
264
Galaxy/S-MAX (CA1) Vehicles Built From: 25-11-2013, Vehicles Built Up To: 18-12-2014, CG3533en enGBR, Edition date: 11/2013, Second Printing
Descargar
Enlace público actualizado
Se ha actualizado el enlace público a tu chat. Puedes ver y gestionar tus enlaces de chat después del registro aquí.
Enlace público del documento
Anuncio
