advertisement
Repairs
9 Repairs
NOTICE
The application tool can be damaged when opening the housing, making changes to the components or if repairs are carried out incorrectly.
f Tool only to be repaired by authorised personnel.
Repair work must only be carried out by the manufacturer or persons authorised by the manufacturer. This also includes opening the application tool and changing components or functions.
9 .1 Replacing the blade
The blade should always be changed when the tie can no longer be cut-off neatly or easily.
CAUTION
The blade is sharp and could cause injury.
f Unscrew the blade holder screws
1
(Figure
H
).
f Remove the blade holder
2
(Figure
H
).
f Remove the blade
3
(Figure
H
) carefully.
f If necessary, replace the punch
5
(Figure
H
) by removing the pin
4
(Figure
H
).
f Insert a new and undamaged blade of the same size and design (see section „Spare parts and accessories“). Observe the correct installation direction.
f Replace the blade holder
2
(Figure
H
).
f Tighten the screw of the blade holder
1
(Figure
H
).
10 Taking out of operation
When used for its intended purpose, the application tool can be used without time limit. In case of disposal, the application tool must be disposed of correctly in accordance with the country-specific disposal guidelines.
Operating instruction • MST9 • 11-2015 • 031-93350
8
advertisement
Related manuals
advertisement
Table of contents
- 10 1 Information on the operating instructions
- 10 2 Intended use
- 10 3 Representation and layout of warning instructions
- 10 4 Initial operation
- 11 5 Overview image
- 11 6 Using the tool
- 12 7 Setting the tension force
- 12 7.1 Setting the tension force via the adjustment dial
- 12 8 Maintenance
- 13 9 Repairs
- 13 9.1 Replacing the blade
- 13 10 Taking out of operation
- 14 11 Spare parts and accessories
- 14 12 Technical data
- 36 Operating instruction • MST
- 16 1 Hinweise zur Betriebsanleitung
- 16 2 Bestimmungsgemäße Verwendung
- 16 3 Darstellung und Aufbau von Warnhinweisen
- 16 4 Inbetriebnahme
- 17 5 Übersichtsbild
- 17 6 Verwendung des Verarbeitungswerkzeuges
- 18 7 Zugkrafteinstellung
- 18 7.1 Zugkraft über den Drehknopf einstellen
- 18 8 Wartung
- 19 9 Reparaturen
- 19 9.1 Messerwechsel
- 19 10 Außerbetriebnahme
- 20 11 Ersatzteile und Zubehör
- 20 12 Technische Daten
- 36 Betriebsanleitung • MST
- 22 2 Utilisation conforme
- 22 d‘avertissement
- 22 4 Mise en route
- 23 5 Image de vue d‘ensemble
- 23 6 Utilisation de l‘outil de pose
- 24 7 Réglage de la tension de serrage
- 24 de la molette de réglage
- 24 8 Maintenance
- 25 9 Réparations
- 25 9.1 Remplacement de la lame
- 25 10 Mise hors service
- 26 11 Pièces de rechange et accessoires
- 26 12 Caractéristiques techniques
- 36 Manuel d’utilisation • MST
- 28 1 Acerca del manual de instrucciones
- 28 2 Finalidad prevista
- 28 3 Representación y estructura de las advertencias
- 28 4 Puesta en marcha
- 29 5 Descripción Imágenes
- 29 6 Uso de la herramienta
- 30 7 Ajuste de la fuerza de tensado
- 30 giratorio
- 30 8 Mantenimiento
- 31 9 Reparaciones
- 31 9.1 Cambio de la cuchilla
- 31 10 Puesta fuera de servicio
- 32 11 Piezas de repuesto y accesorios
- 32 12 Datos técnicos
- 36 Manual de Instrucciones • MST