Draper Speed. MacDon D50 & D60
Add to My manuals160 Pages
MacDon D50 & D60 Harvest Headers are designed to serve a dual function in your grain, hay, and specialty crop harvesting operation. Teamed with your self-propelled windrower power unit and optional hay conditioner, the D50 and D60 Harvest Headers will cut and lay crop into uniform fluffy windrows. Windrowing allows starting the harvest earlier, protects the crop from wind damage, and gives you more flexibility in scheduling combine time.
advertisement
![Draper Speed. MacDon D50 & D60 | Manualzz Draper Speed. MacDon D50 & D60 | Manualzz](http://s1.manualzz.com/store/data/006292089_1-d860313a06bb97e8c412cdfd9ca498fb-360x466.png)
SECTION 7. OPERATION
a. The draper speed is controlled with the windrower
CDM (Cab Display Module). Refer to your Self-
Propelled Windrower Operator’s Manual. b. Adjust draper speed to achieve good feeding of crop onto adapter draper. Excessive draper speed will reduce draper life.
NOTE
If sufficient draper speed cannot be achieved, a possible cause is low relief pressure. Refer to the Technical
Service Manual for checking and adjusting relief pressure.
7.12.7.1 Knife Speed Guidelines
Recommended Knife
Speed Range
(RPM)
Header Size
15 FT.
SK
(Single Knife
Header on SP
Windrower)
---
DK
(Double Knife
Header on SP
Windrower)
750 - 950
20 and 25 FT.
30 FT.
35 FT.
600 - 750
600 - 700
550 - 650
700 - 850
600 - 800
600 - 750
40 FT. 525 - 600 550 - 700
The header sickle drive is driven by the windrower hydraulic pump and is controlled with the windrower CDM.
The default speed is 600 revolutions per minute
(rpm). Refer to your Self-Propelled Windrower
Operator’s Manual.
Refer to the following charts for guidelines on the recommended knife speeds to suit a particular crop.
A chart is provided for each header size or range of sizes and whether the header is a single (SK) or double knife (DK) machine.
Refer to examples below each chart.
950
925
900
875
850
825
800
775
750
725
700
1
15 Foot Double Knife
GROUND SPEED (km/hr)
975
1.6
3.2
4.8
6.4
8.0
9.7
11.3
12.9
2 3
14.5
1950
1900
1850
1800
1750
1700
1650
1600
1550
1500
1450
9
1400
15 DK
FORAGE RANGE
GRASS RANGE
4 5 6 7 8
GROUND SPEED (miles/hr)
Example
: Cutting Forage at 5.0 mph (8.0 km/hr)
Use Knife Speed Between 850 - 900 rpm (1700 -
1800 spm).
Form 169441
40
Revision B
875
1.6
850
825
800
775
750
725
700
675
650
625
600
1
3.2
2
4.8
3
SECTION 7. OPERATION
20 and 25 Foot Single and Double Knife
GROUND SPEED (km/hr)
6.4
8.0
9.7
11.3
12.9
4 5 6
GROUND SPEED (miles/hr)
7 8
14.5
1750
1700
1650
1600
1550
1500
1450
1400
1350
1300
1250
1200
9
20-25 FT DRAPER
DK GROUP A RANGE
DK GROUP B RANGE
SK GROUP A RANGE
SK GROUP B RANGE
Group A: Forage/Alfalfa/Flax
Group B: Canola/Cereals/Edible Beans
Example: Cutting Group A Crops at 5.0 mph (8.0 km/hr) With Single Knife
Use Knife Speed Between 710 - 735 rpm (1420 - 1470 spm).
30 Foot Single and Double Knife
675
650
625
600
575
550
1
825
1.6
800
775
750
725
700
3.2
2
4.8
3
GROUND SPEED (km/hr)
6.4
8.0
9.7
11.3
12.9
14.5
1650
1600
1550
1500
1450
1400
1350
1300
1250
1200
30 FT DRAPER
DK GROUP A MAX
DK GROUP A MIN/GROUP B MAX
DK GROUP B MIN
SK GROUP A & B RANGE
1150
4 5 6
GROUND SPEED (miles/hr)
7 8 9
1100
Example: Cutting Group A or B Crops at 5.0 mph (8.0 km/hr) With Double Knife
Use Knife Speed Approximately 680 rpm (1360 spm).
Group A: Forage/Alfalfa/Flax
Group B: Canola/Cereals/Edible Beans
Form 169441
41
Revision B
775
1.6
750
725
700
675
650
625
600
575
550
525
500
1
700
675
650
625
775
1.6
750
725
600
575
550
525
500
1
SECTION 7. OPERATION
35 Foot Single and Double Knife
3.2
2
3.2
2
4.8
3
4.8
3
GROUND SPEED (km/hr)
6.4
8.0
9.7
11.3
12.9
14.5
1550
1500
1450
1400
1350
1300
1250
1200
1150
1100
9
1050
1000
35 FT DRAPER
DK FLAX MAX
DK CEREALS MAX/FLAX MIN
DK CEREALS MIN
SK FLAX MAX
SK CEREAL MAX/FLAX MIN
SK CEREAL MIN
4 5 6
GROUND SPEED (miles/hr)
7 8
Example: Cutting Flax at 5.0 mph (8.0 km/hr) With Single Knife.
Use Knife Speed Between 600 - 650 rpm (1200 - 1300 spm).
40 Foot Single and Double Knife
GROUND SPEED (km/hr)
6.4
8.0
9.7
11.3
12.9
14.5
1550
4 5 6
GROUND SPEED (miles/hr)
7 8
1500
1450
1400
1350
1300
1250
1200
1150
1100
1050
9
1000
40 FT DK DRAPER
DK FLAX RANGE
DK CEREALS RANGE
SK FLAX RANGE
SK CEREAL RANGE
Example:
Cutting Fl ax at 8.5 mph (13.7 km/hr) With Single Knife
Use Knife Speed Between 595 - 645 rpm (1190 - 1290- spm).
NOTE:
Close to maximum Single Knife Speed for 40 ft .which may result in ragged cutting. Double Knife machine allows higher knife speed and clean cutting.
Form 169441
42
Revision B
advertisement
Key Features
- Cuts and lays crop into uniform fluffy windrows
- Allows starting the harvest earlier
- Protects the crop from wind damage
- Gives you more flexibility in scheduling combine time
- Designed for self-propelled windrowers
- Optional hay conditioner available
Related manuals
Frequently Answers and Questions
What is the purpose of MacDon D50 & D60 Harvest Headers?
What types of crops can be harvested with MacDon D50 & D60 Harvest Headers?
Do MacDon D50 & D60 Harvest Headers work with all self-propelled windrowers?
Can I use a hay conditioner with MacDon D50 & D60 Harvest Headers?
advertisement
Table of contents
- 3 INTRODUCTION
- 4 MODEL AND SERIAL NUMBER
- 8 SAFETY
- 8 SAFETY ALERT SYMBOL
- 8 SIGNAL WORDS
- 8 SAFETY SIGNS
- 8 Safety Sign Installation
- 9 Safety Sign Locations
- 18 GENERAL SAFETY
- 20 DEFINITIONS
- 21 COMPONENT IDENTIFICATION
- 22 SPECIFICATIONS
- 24 OPERATION
- 24 OWNER/OPERATOR RESPONSIBILITIES
- 24 OPERATIONAL SAFETY
- 25 HEADER ATTACHMENT/DETACHMENT
- 25 Attachment
- 26 Detachment
- 28 BREAK-IN PERIOD
- 28 PRE-SEASON CHECK
- 29 DAILY START-UP CHECK
- 29 SHUTDOWN PROCEDURE
- 30 HEADER CONTROLS
- 30 HEADER LIFT CYLINDER LOCK-OUTS
- 31 REEL PROPS
- 32 HEADER SET-UP
- 36 HEADER OPERATING VARIABLES
- 36 Cutting Height
- 38 Header Float
- 39 Header Angle
- 40 Reel Speed
- 41 Ground Speed
- 42 Draper Speed
- 42 Knife Speed
- 45 Reel Height
- 45 Reel Fore-Aft Position
- 50 Reel Tine Pitch
- 52 Crop Dividers and Rods
- 55 DELIVERY OPENING/DECK SHIFT
- 55 Delivery Opening - D
- 57 DOUBLE WINDROWING
- 57 Hydraulic Deck Shift
- 57 Manual Deck Shift
- 59 WINDROW TYPES
- 60 HAYING TIPS
- 60 Curing
- 60 Topsoil Moisture
- 60 Weather And Topography
- 60 Windrow Configuration
- 60 Driving on Windrow
- 60 Raking And Tedding
- 61 Chemical Drying Agents
- 62 DRAPER DEFLECTORS
- 62 Deflector Replacement
- 62 Deflector Rework
- 63 HEADER LEVELLING
- 63 UNPLUGGING CUTTERBAR
- 64 UPPER CROSS AUGER
- 65 TRANSPORTING HEADER
- 65 On The Windrower
- 65 Towing
- 66 Converting from Transport to Field Position
- 71 Converting from Field to Transport Position
- 73 STORAGE
- 74 MAINTENANCE AND SERVICING
- 74 PREPARATION FOR SERVICING
- 74 RECOMMENDED SAFETY PROCEDURES
- 75 MAINTENANCE SPECIFICATIONS
- 75 Recommended Torques
- 77 Roller Chain Installation
- 77 Sealed Bearing Installation
- 78 Recommended Fluids and Lubricants
- 78 Conversion Chart
- 79 ENDSHIELDS
- 79 Hinged
- 81 Non-Hinged
- 82 LUBRICATION
- 82 Greasing Procedure
- 82 Lubrication Points
- 88 Oiling Requirements
- 89 Hoses and Lines
- 90 Hydraulic Schematics
- 94 ELECTRICAL
- 95 SICKLE AND SICKLE DRIVE
- 95 Sickle Sections
- 96 Sickle Removal
- 96 Sickle Head Bearing Replacement
- 97 Sickle Installation
- 97 Spare Sickle (Single Knife Headers)
- 98 Sickle Guards
- 101 Sickle Hold-Downs
- 102 Sickle Drive Belts - Non-Timed Drive
- 103 Sickle Drive Belts - Timed Drive
- 108 Wobble Box
- 111 DRAPERS
- 111 Draper Tension Adjustment
- 112 Replacing Split Draper
- 113 Replacing Endless Draper
- 115 Draper Alignment
- 116 Draper Roller Maintenance
- 119 Deck Height
- 120 REEL AND REEL DRIVE
- 120 Reel Clearance to Cutterbar
- 121 Reel Frown Adjustment
- 122 Reel Centering
- 123 Reel Drive Chain - D
- 128 Reel Drive Sprocket - D
- 130 Reel Drive U-Joint - D
- 131 Reel Drive Motor - D
- 133 Reel Speed Sensor
- 134 Reel Tines
- 136 Tine Tube Bushings
- 140 TRANSPORT SYSTEM
- 140 Wheel Bolt Torque
- 140 Axle Bolts
- 140 Tire Inflation
- 141 MAINTENANCE SCHEDULE
- 141 Break-In Inspections
- 142 Interval Maintenance
- 143 Maintenance Record
- 144 TROUBLESHOOTING
- 144 CROP LOSS AT CUTTERBAR
- 145 CUTTING ACTION AND SICKLE COMPONENTS
- 147 REEL DELIVERY
- 149 HEADER AND DRAPERS
- 150 CUTTING EDIBLE BEANS
- 153 WINDROW FORMATION
- 154 OPTIONS AND ATTACHMENTS
- 154 CUTTERBAR POLY
- 154 ADJUSTABLE SKID SHOES WITH POLY COVER
- 154 STUB GUARD CONVERSION KIT
- 154 STABILIZER WHEELS
- 154 STABILIZER/TRANSPORT WHEELS
- 155 LODGED CROP REEL FINGER KIT
- 155 VERTICAL KNIFE MOUNTS
- 155 UPPER CROSS AUGER KIT
- 155 REEL ENDSHIELD KIT
- 155 DOUBLE DRAPER DRIVE
- 156 DRAPER EXTENSION KIT
- 156 RICE DIVIDER KIT
- 156 KNIFE HEAD SHIELD
- 156 SWATH FORMING RODS
- 156 HYDRAULIC DECK SHIFT
- 156 DOUBLE WINDROW ATTACHMENT
- 157 HAY CONDITIONER
- 157 ROCK RETARDER KIT
- 157 HYDRAULIC REEL FORE-AFT POSITIONER
- 158 UNLOADING AND ASSEMBLY