Assembly of the Pasta Attachments (See Fig. E). BOMANN KM 1395 CB , KM 1395

Assembly of the Pasta Attachments (See Fig. E)

NOTE:

If the pasta dough is very sticky, lubricate the worm with a few drops of cooking oil.

Proceed as described under

“Preparation”

.

6. Select a pasta attachment (34).

7. Place the attachment on the axis of the spiral. Pay attention to the recesses on the pasta attachment.

More details can be found under

“Attach Preassembled

Worm Housing”

.

Attach Preassembled Worm Housing

8. Screw the locking ring (28) clockwise onto the spiral housing.

9. Attach the pre-assembled worm housing to the appliance.

Position the worm housing with the arrow ( ) aligned with ( ) on the appliance. Turn to the upright position.

The arrow on the worm housing must be opposite the arrow on the appliance. (Refer to the figure.)

CAUTION:

If you open and close the ring nut again after attaching it, hold the worm housing securely with one hand on the filler neck (23), otherwise the worm housing may accidentally come loose.

10. Position the filler tray (22) so that the bed of the tray lies above the arm (7).

Operation of the Meat Grinder

WARNING: Risk of injury!

• Once you turn on the appliance, the drive shaft of the kneading machine starts rotating. Do not reach into the rotating drive shaft during operation!

• Always mount the bowl for your safety.

• Always use the supplied pusher. Never put fingers or tools into the filler neck!

CAUTION:

Never

use the meat grinder with attached bowl! Cover the drive shaft of the mixing drive with the safety cover (6).

11. Put the pieces of meat (meat paste / sausage mass or dough) on the filling tray and into the filler neck.

12. Plug the power cord into a properly installed earthed socket.

13. You can select a speed from level 4 to 8.

14. Stuff, if necessary, the meat respectively the dough with the stuffer (21).

62

NOTE:

Short-term operation:

Operate the appliance with the meat grinder no longer than 10 minutes and allow the appliance to cool down for 10 minutes.

Complete Operation

1. Turn the rotary knob anticlockwise until the display shows

“ ”.

2. Disconnect the power plug.

3. Disassemble all parts of the meat grinder.

4. Clean the parts used as described under

“Cleaning”

.

5. Cover the uptake for the spiral housing with the cover (15).

The Mixer

Application Instruction for the Mixer

WARNING: Risk of injury!

•

The knife in the mixer is sharp!

Handle the blades of the mixer with the necessary care, especially when emptying and cleaning the mixing bowl!

• Once you turn on the appliance, the drive shaft of the kneading machine starts rotating. Do not reach into the rotating drive shaft during operation!

• Always mount the bowl for your safety.

CAUTION:

•

Never

press the release button (10), if you have placed the mixing bowl! The mixing bowl tilts.

• Do not operate the mixer without food!

• The glass could crack at high temperatures! Do not fill in liquids over 60 °C.

• Do not overfill the mixing bowl! Fill in a maximum of

1500 ml (fruit and liquid).

• Foam takes a lot of volume. Reduce the capacity for liquids that foam vigorously.

• Cut the food into small pieces before operating the appliance.

• Do not fill any hard ingredients such as nuts or coffee beans into the mixing bowl.

• Objects like spoons or scrapers never may be in the mixing vessel during operation.

NOTE:

The knives in the mixing vessel are also suited to crush small amounts of pure ice. Remember, however, that the operation may blunt the knife.

Recommendation:

If you want to prepare drinks with crushed ice, add the ice cubes during mixing. The ice is crushed during mixing.

Place the mixing bowl on a stable level surface when filling it.

So you can better place the cover afterwards.

KM1395CB_IM 22.06.17