advertisement
Making Printer Settings Using the Control Panel
❒ The signal is rated [Good] if signal strength is 86%-100%, [Fair] if 61%-85%,
[Poor] if 31%-60%, and [Unavailable] if 0%-30%. If the signal is unstable or unavailable, remove any obstructions or move the printer to a place to receive the signal.
❒ Using wireless devices or microwave sources nearby will affect the signal transmission.
Resetting the IEEE 802.11b (Wireless LAN) Settings
Follow the procedure below to reset the wireless LAN setting on the [Maintenance] menu.
❒ [Comm. Mode], [Channel], [Trans. Speed], [WEP Setting], and [SSID] can be selected on the [Host Interface] menu.
A
Press the {Menu} key.
The [Menu] screen appears.
B
Press the {T} or {U} key to display [Maintenance], and then press the {#
Enter} key.
C
Press the {T} or {U} key to display [WL.LAN Defaults], and then press the
{# Enter} key.
D
Press the {# Enter} key.
The wireless LAN setting is reset.
After about three seconds, the initial screen appears.
Maintenance menu parameters
This section explains about parameters that can be set on the Maintenance menu.
❖ Color Regist.
You can specify Auto Adjust or Fuser Adjust for this feature.
134
Making Printer Settings Using the Control Panel
❖ Color Calibrate
You can adjust the gradation of bright (highlighted parts) and medium areas
(middle parts) for printing.
❖ Start Calibr. 1
You can print gradation correction sheet 1.
❖ Start Calibr. 2
You can print gradation correction sheet 2.
❖ Reset
You can reset the gradation correction value to default.
For details, see “Correcting the Color Gradation”, Maintenance Guide.
❖ Image Density
You can select the print image density.
❖ Prt. Test Sheet
You can print the image density test sheet.
❖ Black, Cyan, Magenta, Yellow
-10 to 10
❖ Reset
Reset the image density value to default.
For details, see “Adjusting the Image Density”, Maintenance Guide.
❖ Registration
You can adjust the starting position of the printing page.
❖ Prt. Test Sheet
You can print the registration test sheet.
• Tray 2
• Tray 3
• Duplex.BackSide
❒ Only the installed trays appear on the display panel.
❖ Adjustment
You can select the start position for printing on a page.
• Horiz: Tray 2
• Horiz: Tray 3
• Horiz:Dup.Back
135
Making Printer Settings Using the Control Panel
❒ Only the installed trays appear on the display panel.
❖ Plain Paper
You can specify plain paper for each tray.
• Tray 1
• Tray 2
• Tray 3
• Bypass Tray
❒ Default: Normal
❖ Maint. Reset
Maintenance Reset allows the user to reset the counters of each internal unit, such as the Transfer Belt and Fusing Unit. These counters can be reset at anytime, but must be reset when a unit is reinstalled.
For details about resetting internal units, see "Replacing Consumables",
Maintenance Guide.
❖ HD Format
You can format the hard disk when the optional hard disk is installed.
For details about formatting the hard disk, see “Attaching Printer Hard Disk
Type 3000”, Setup Guide.
❖ 4C.Graphic Mode
This mode adjusts levels of toner color overlap. If characters or lines blur, selecting [Text Priority] may make them clearer. Select [Photo Priority] for normal use.
❒ Default: Photo Priority
❖ Replacmnt Alert
Use this function to specify when to warn the user about replacing supplies.
• Notify Sooner
• Normal
• Notify Later
❒ Default: Normal
❖ WL.LAN Signal
You can check the signal strength when using wireless LAN.
136
Making Printer Settings Using the Control Panel
For details about displaying the signal strength, see p.133 “Displaying the signal strength” .
❖ WL.LAN Defaults
Reset the wireless LAN to default. The menu appears when the 802.11b interface unit is installed.
❖ Image Area
You can extend the printable area by about 2.5 mm (0.01 inch).
• Do not enlarge
• Enlarge
❒ Default: Do not enlarge
❖ Key Repeat
Holding down [On] allows users to scroll through items and settings. Pressing
[Off] moves through items and settings one at a time.
❒ Default: On
137
advertisement
Related manuals
advertisement