Functions of NT20
Section 1-2
1-2 Functions of NT20
The NT20 has the following features which are different from those of existing
NT20M/NT20S;
1-2-1 Features
Downsized Body
• The connectors are located at other than the front.
• The communications cable connectors are housed in the unit so that they do not protrude from the unit.
• The tool connectors and the Host communications connectors are used in common (when the host link/NT link is used).
Construction Best Suited to the FA Environment
• Easy-to-read screen even in direct sunlight.
• Long-lived backlight leads free from maintenance.
• Waterproof structure equivalent to oil-resistant IP65.
256 dots
128 dots
Wide angle of visibility
±35°
A Host Link I/F Unit, Screen Data Memory, and a System ROM Are All Incorporated
• With the NT link communications method, 1:1 connections and 1:N connections are possible.
• There is no complicated installation work except a simple connection to a
Host.
• A flash memory is used for the screen data memory. There is no need of backup battery.
• The following communications methods are standard for each model:
NT20-ST121-E: Host Link (direct) and NT Link
NT20-ST121-E + NT20-IF001 + NT600M-LB122-V1: C200H direct communications
NT20-ST128: RS-232C communications (command control)
• The NT20 can be connected to Mitsubishi FX-series and Mitsubishi Aseries PLCs. (Refer to PLC Connection, Operation Manual (Cat. No.
V042-E1@)).
Touch Switch Operation
The System Menu can be displayed by using the touch switches located in four corners of the screen.
Compatibility with NT20M/
NT20S
Existing screen data, user programs, are compatible.
4
Functions of NT20
1-2-2 Principal Functions of NT20
Functions Related to the Data Display
• Character display
Characters of various sizes can be displayed. Characters can flash or be highlighted.
• Figure display
Straight lines, circles, and other graphic figures can be displayed.
• Memory data display
Contents of the character-string memory table and the numeral memory table can be displayed. The memory table contents can be changed from the PLC/Host.
• Bar graph display
Bar graphs corresponding to the contents of the numeral memory table can be displayed.
• Lamp display
Lamps which turn on or flash as controlled by the Host can be displayed.
Section 1-2
Functions Related to the Data Input
• Input by the touch switch
Data can be input by simply touching the screen.
• Numeric setting function
The touch keys can be assigned with numeric values so that the numeric values can be input at the operation site and sent to the PLC/Host.
Other Functions
• Buzzer
A built-in buzzer can be used.
• Communications with a PLC
By connecting the NT20 with a PLC using the host link, NT link, C200H, or RS-232C communications method, data can be received from the host and touch switch status information can be sent to the host.
• System function
The system setting and maintenance can be executed by using the
System Menu on the screen.
• Screen data creation
The screen data can be created by using support tools on the computer and stored in the unit.
• Unrestricted screen display
When the NT20 is connected to the host via an RS-232C interface, characters and graphics can be displayed independently of the registered screens (terminal function) (only with NT20-ST128).
5
Functions of NT20
Section 1-2
1-2-3 Comparison between NT20S, NT20M, and NT20
The NT20 is a unitary PT which incorporates a system ROM, screen memory, and a host I/F unit (Host link, NT link, RS-232C, and C200H direct communications) as the standard equipment in one body.
The NT20 has the following features which are different from those of existing
NT20/NT20S:
Function
Communications
Communications connector
NT20S
• Host link/NT link incorporated NT20S-ST121-EV3
• C200H direct communications incorporated
NT20S-ST122-V1
• RS-232C incorporated
NT20S-ST128
(other host I/F units cannot be connected)
NT20M-DT121-V2
Host I/F units are required.
NT20
• Host link/NT link
• C200H direct communications
Host I/F unit for C200H communications is required.
• RS-232C incorporated
NT20-ST128 (other host I/F units can not be connected)
• The communications connector (9-pin) for a Host is shared with that for the Support Tool. (NT20S-ST121-
EV3/ST128)
• Connectors for Support Tool
(9-pin) and Host connections on the rear face
(NT20S-ST122-V1).
Not provided
The Support Tool connector
(9-pin) is located on the front.
The Host connector (25-pin) is located on the back.
Provided
• The communications connector (9-pin) for a Host is shared with that for the Support Tool. (Port A)
• The communications connector (9-pin) for a Host
(Port B)
Not provided Host RUN input terminal/
Alarm output terminal
System keys
Contrast control
Waterproof performance
Not provided
Back
Equivalent to oil-resistant
IP65
Not guaranteed
Provided
Front
Conforms to IP54F.
5 ms Allowable momentary power interruption time
System ROM Built in (not replaceable)
Not provided
Back
Equivalent to oil-resistant
IP65
Not guaranteed
Resume function Not provided
History retaining function Not provided
Screen transfer
❍
Screen data compatibility
❍ (Note)
PLC ladder compatibility
❍
Backlight replacement
❍
Screen data memory Built in (flash ROM only)
Screen data memory capacity
Outside dimensions
96KB
190
× 110 × 58 mm
System ROM compatible with host I/F unit is required.
Flash ROM rewriteable
Provided Not provided
Provided
❍ (Only possible if screen data memory is an SRAM)
Not provided
❍
–
–
❍ (Note)
❍
Possible with NT20M-DT131. Do not need
Built in (Flash ROM) Optional (select from
EPROM, SRAM, and
EEPROM)
128 KB max.
512 KB
220
× 110 × 82 mm
190
× 108 × 53.5 mm
Note
If a system key function is required on continuous screens or for numerical setting or buzzer stop, use the Support Tool and set the touch switches which have the system key function in such screens.
For details, refer to 4-7-3 System Key Functions on page 154.
6
Functions of NT20
1-2-4 Displays
Characters
(character string)
Characters (text)
Bar graph
Section 1-2
The NT20 can display various kinds of elements such as characters, lamps, touch switches, and bar graphs on a screen. The screen data displayed on the
NT20 are created by using the Support Tool on a computer.
Touch switches
Line 1 Status
Machine name : NT20
Production qty. : 137 units
Emergency stop
Restart
Numeric value
(Numeral table)
0%
Stage 1
50%
Stage 2
100%
30%
Stage 3
Lamps
Characters (Text)
Characters and marks which do not need to be changed can be written directly to the screen.
Characters (Character-string Memory Table)
Character-strings stored in the character-string memory table are displayed.
The display characters can be changed by changing the data stored in the character-string memory table.
Numeric Values (Numeral Table)
Numbers stored in the numeral table are displayed. The display numbers can be changed by changing the data stored in the numeral table. Hexadecimal values can also be displayed.
Lamps
Touch Switches
Numeric Keys
Bar Graphs
Lamps are displayed as square or round frames and indicate the operating status. They are controlled by the Host and can be lit (reversed) or made flash
(alternates normal with reversed displays).
Touch switches can be set anywhere on the screen. Touching the screen at a touch switch location can switch the display (display switch function) or notify the Host (notification function). The touch switches can be lit or made flash by controlling from the Host in the same way as the lamps.
These are the touch switches used to input numeric values.
Marks
The bar graph extends and contracts in proportion to the data stored in the numeral table. A percentage value can also be displayed simultaneously.
Marks can be designed, created, and handled like characters by the user.
7