Before Operating
Section 1-6
1-6 Before Operating
Follow the procedure given below to start the system of the NT20.
Host
Set the host settings.
• For the Host Link, refer
to page 44, and the man-
uals for the Host Link
Unit and Programming
Device.
• For a 1:1 NT Link, refer
to page 56.
• For 1:N NT Links, refer to
page 60.
• For high-speed 1:N NT
Links, refer to page 65.
• When using C200H direct communications, no settings are required.
• For RS-232C, refer to
page 79 and the manu-
als for the Host.
NT20
Set the DIP switch pins.
(page 19)
Install the PT in the operation panel.
(page 22)
NT Support Tool
Install the NT Support
Tool in the computer.
(Refer to the NT Support Tool
Operation Manual.)
Connect the power supply and peripheral device.
(page 23)
Install the system program.
(See note.)
(Refer to page 126 and the NT
Support Tool operation manual.)
Transmit the screen data.
Create the screens.
(Refer to the NT Support Tool
Operation Manual.)
(page 102)
Connect to the NT20.
Set the memory switches.
(page 91)
Connect to the host.
Create the host program.
Confirm the settings and check communications.
Note
Start operation.
System program installation is only done in special circumstances, for example when changing the system program, or when recovering the original status of the installed program. This operation is not normally necessary.
14
Before Operating
Section 1-6
Refer to the following manuals for the equipment and software.
Device or Software
NT20 User’s Manual
System Installer
NT Support Tool
PLC
Manual Title
NT-series Support Tool for Windows (Ver. 4.8) Operation Manual
NT-series Support Tool for Windows (Ver. 4.8) Operation Manual
SYSMAC CPM1 Operation Manual
SYSMAC CPM1A Operation Manual
SYSMAC CPM2A Operation Manual
SYSMAC CPM2C Operation Manual
SYSMAC C200H Operation Manual (for CPU01/03/11) (Programming)
SYSMAC C200H Operation Manual (for CPU21/23/31) (Programming)
CompoBus Master
Control Unit
Programming Tools SYSMAC Support Software Operation Manual: C-series PLCs
Host Link Unit/
Serial Communications Board
SYSMAC C200HS Installation Guide
SYSMAC C200HS Operation Manual (Programming)
SYSMAC C200HX/HG/HE (-Z) Installation Guide
SYSMAC C200HX/HG/HE Operation Manual
SYSMAC C200HX/HG/HE-Z Operation Manual
SYSMAC CQM1/CPM1/CPM1A/SRM1 Programming Manual
SYSMAC CQM1H Operation Manual
SYSMAC CVM1/CV500/CV1000/CV2000/CVM1 Operation Manual: Ladder Diagrams
CS Series Programmable Controllers Operation Manual
CJ Series CJ1G-CPU @@-E Programmable Controllers Operation Manual
CS/CJ Series Programming Manual
CS/CJ Series Serial Communications Boards/Units Operation Manual
SYSMAC CQM1H Series Serial Communications Board Operation Manual
SRM1 (-V2) Operation Manual
SYSMAC Support Software Operation Manual: CVM1 PLCs
SYSMAC CPT User Manual and Quick Start Guide
CX-Programmer Ver. 4 User Manual
SYSMAC C Series Host Link Unit System Manual
SYSMAC CVM1/CV Series Host Link Operation Manual
SYSMAC C200HW-COM01 C200HW-COM02-V1 to C200HW-COM06-EV1 Communications Board Operation Manual
W339-E1-
@
W393-E1@
W394-E1@
W336-E1@
W365-E1-
@
W318-E1@
W248-E1@
W249-E1@
W332-E1-
@
W333-E1-
@
W425-E1@
W143-E1@
W205-E1@
W304-E1-
@
Cat. No.
V091-E1@
V061-E1-
@
V061-E1@
W262-E1@
W317-E1@
W352-E1-
@
W356-E1@
W130-E1@
W217-E1@
W236-E1-
@
W235-E1@
W302-E1@
W303-E1@
W322-E1-
@
W228-E1@
W363-E1@
W202-E1@
15
Before Operating
Section 1-6
16
SECTION 2
Hardware Settings and Connections
This section describes the settings of the NT20, connections to a Host, and other hardware settings.
2-1 Description of Parts and Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-1-1 Description of Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-1-2 Operation Status DIP Switch Settings . . . . . . . . . . . . . . . . . . . . . . .
2-2 Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-2-1 Installation Environment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-2-2 Installation to the Operation Panel . . . . . . . . . . . . . . . . . . . . . . . . . .
2-2-3 Power Supply Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-3 Connecting Link Adapters and RS-422A Converters . . . . . . . . . . . . . . . . . . .
2-3-1 Connecting an CJ1W-CIF11 RS-422A Converter . . . . . . . . . . . . . .
2-3-2 Connecting an NT-AL001 Link Adapter . . . . . . . . . . . . . . . . . . . . .
2-4 Connecting the NT Support Tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-5 Using a Memory Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-5-1 Installation Method. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-5-2 Method of Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-6 Connecting to the RS-232C Port at the Host . . . . . . . . . . . . . . . . . . . . . . . . .
2-6-1 Host Types and Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-6-2 Connecting Directly between RS-232C Ports . . . . . . . . . . . . . . . . .
2-7 Communicating with the PLC Using C200H Direct Communications . . . . .
2-7-1 Applicable PLC Units. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-7-2 Connection Method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-7-3
Turning the Power ON/OFF When Using C200H Direct
Communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-8 Host Connections by RS-232C (NT20-ST128) . . . . . . . . . . . . . . . . . . . . . . .
2-8-1 Host Computer Communications Settings . . . . . . . . . . . . . . . . . . . .
2-8-2 Connector Pin Arrangement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
36
37
37
44
24
24
28
35
44
69
73
73
73
21
21
22
23
18
18
19
77
79
79
79
17