Operation Modes and the System Menu
Section 3-3
3-3 Operation Modes and the System Menu
The NT20 operates in either “RUN”, “Transmit”, or “Maintenance” mode. The operation modes can be changed by using the System Menu.
3-3-1 System Menu and the Operation Modes
Select an operation mode by pressing the corresponding touch switch in the
System Menu. The operation modes with respect to the System Menu are related to each other as shown below.
For the operations with the System Menu, refer to the 3-3-3 Operations with
the System Menu (page 86).
RUN mode
The NT20 runs in this state. Controls from the
Host are enabled and various indications and
I/O operations are made.
Power ON
When system settings and screen data registration have been completed
To change system settings or screen data contents
[ SYSTEM MENU ]
Quit
Transmit Mode
Maintenance mode
Transmit mode
Screen data and other data are transmitted between the NT20 and a support tool.
Maintenance mode
The NT20 maintenance operations such as memory initialize and setting check are executed.
3-3-2 Menu Tree
The System Menu allows to effect various NT20 functions by using the touch switches. The NT20’s functions with respect to the System Menu are related as shown below.
For the operations with the System Menu, refer to the 3-3-3 Operations with
the System Menu (page 86).
84
Operation Modes and the System Menu
Section 3-3
SYSTEM MENU
Quit
Transmit Mode (page 86)
Maintenance Mode
MAINTENANCE MENU
Quit
PT Setting (page 107)
I/O Check
Init. Memory
Memory Switch
DIP-SW Status (page 109)
Note
I/O CHECK MENU
Quit
LED Check (page 105)
Buzzer (page 104)
Touch Switch (page 99)
Data Memory (page 106)
LCD Display (page 103)
Comm. Check
Host Link, NT Link, C200H
Direct Communications
COMM. CHECK MENU
Quit
Tool I/F
RS-232C (NT20-ST128)
COMM. CHECK MENU
INITIALIZE MEMORY MENU
Quit
Init. Screen (page 88)
Host Link, NT Link
MEMORY SWITCH MENU
Quit
Tool I/F (page 101)
RS-232C I/F
Comm. Type
(page 93)
Key Sound
(page 106)
Buzzer Sound
(page 107)
BK light Off
(page 109)
Tool Mode
(page 111)
Automatic Reset
(page 98)
Unit No.
(page 97) (See note 1.)
Baud Rate
(pages 95, 96)
Comm. Port
(page 94)
Language
(page 110)
First screen
Second screen
C200H Direct Communications
MEMORY SWITCH MENU
Comm. Type
Key Sound
Buzzer Sound
BK light Off
(page 93)
(page 106)
(page 107)
(page 109)
Tool Mode
Language
(page 111)
Automatic Reset
(page 98)
(page 110)
RS-232C (NT20-ST128)
MEMORY SWITCH MENU
First screen
Second screen
Key Sound
(page 106)
Buzzer Sound
(page 107)
BK light Off
(page 109)
Tool Mode
(page 111)
Automatic Reset
(page 98)
Data Bits
(page 99)
Stop Bits
(page 99)
Partiy Check
(page 99)
Flow Control
(page 99)
Baud Rate
(page 99)
LMP Bit Control
(page 112)
Comm. Port
(page 94)
Lanugage
(page 110)
First screen
Second screen
Third screen
The unit number must be set only for 1:N NT Link communications.
85
Operation Modes and the System Menu
Section 3-3
3-3-3 Operations with the System Menu
The following gives the procedure to call the System Menu, select the menu items, and other operations with the System Menu.
Make sure that DIP SW2-3 “Switch to the System Menu enabled/disabled” is set to OFF (enabled). If the setting is ON (disabled), the System Menu will not be displayed by following the procedure given below.
Displaying the System
Menu
Press appropriate touch switches to display the System Menu as described below. The “RUN” LED goes off when the System Menu is displayed.
The NT20 display screen has four touch switches to display the System Menu in the four corners (about 9 mm x 9 mm size). Press any two of these switches at the same time to call the System Menu screen.
RUN mode
Press any two of these four corners at the same time.
[SYSTEM MENU]
Quit
Transmit Mode
Maintenance mode
Note that the touch switches used to call the System Menu are not displayed on the screen. If a touch switch displayed in a corner is pressed first, the touch switch will function and the System Menu will not be displayed. To successfully call the System Menu, first press a corner where no touch key is displayed, and then, press any other corner regardless of the presence of a touch key.
If a screen has the touch switches registered at all of the four corners, it is impossible to call the System Menu from the screen.
A “system key” function can be assigned to a touch switch. Pressing the touch switch so assigned on the screen can easily display the System Menu. For the
relationship between the system key and the touch switch, refer to the 4-7-3
System Key Functions (page 154).
86
Operation Modes and the System Menu
Selecting the Menu Items
Section 3-3
Press (touch) a menu item on the screen to select the item.
Menu items allow to make the ON/OFF selection or to call subsequent menu or screen.
Example 1
To call the “Maintenance mode menu” by pressing the “Maintenance Mode” on the System Menu screen:
Select “Maintenance Mode”.
[ SYSTEM MENU ]
Quit
Transmit Mode
Maintenance Mode
System Menu Items
Switching from the
System Menu to the RUN
Mode
[ MAINTENANCE MENU ]
Quit DIP-SW Status
PT Setting
I/O Check
Init. Memory
Memory Switch
The System Menu items and the functions are as given below.
Quit
Menu Item Function
The System Menu screen is cleared and the NT20 will return to the RUN mode.
Transmit Mode The Transmit Mode screen will be displayed to allow the transmission of the screen data between the NT20 and the Support
Tool. For the transmission of the screen data, refer to3-6 Regis-
tering the Screen Data (page 102).
Maintenance Mode The MAINTENANCE MENU will be displayed to allow the maintenance of the NT20 system.
The NT20 will exit the System Menu and switch to the RUN mode in the cases described below.
• Selecting “Quit” in the System Menu.
• The screen (touch switches) is not pressed for over 10 seconds.
87