System Maintenance
Section 3-9
3-9 System Maintenance
The NT20 has the self maintenance functions such as I/O check and setting status check.
3-9-1 I/O Check
The I/O operations for the following items of the NT20 are checked by the I/O check function.
• Touch Switch
• Communications with the Support Tool
• Communications with the Host (NT20-ST128 RS-232C only)
• LCD
• LED Check
• The Screen Data Memory
• Buzzer
Checking the Touch Switches
Execute a touch switch check by the menu operation from the System Menu as described below.
Select “Maintenance Mode”.
[ SYSTEM MENU ]
Quit
Transmit Mode
Maintenance Mode
[ MAINTENANCE MENU ]
Quit DIP-SW Status
PT Setting
I/O Check
Init. Memory
Memory Switch
Select “I/O Check”.
[ I/O CHECK MENU ]
Quit LCD Display
Comm. Check LED Check
Buzzer
Touch Switch
Data Memory
Select “Touch Switch”.
115
System Maintenance
Section 3-9
A panel of 6-row x 12-column touch switches, each switch sized 1 x 1 cm, will be displayed.
"EXIT" switch to exit the touch switch check menu.
The touch switch is normal if it is highlighted while it is pressed.
Note
Checking the
Communications with the
Support Tool
• Press a touch switch on the screen. If the touch switch is highlighted while it is pressed, the touch switch is normally functioning.
• When the check is finished, press the EXIT touch switch. The I/O check menu will be redisplayed.
If memory switch setting for the key press sound has been made for ON, the key press sound will be made when a touch switch is pressed.
The status of touch switches pressed during an I/O check is not sent to the host.
Execute a NT20-to-Support Tool communications check by the menu operation from the System Menu as described below.
The NT20-ST121-E/ST128 uses the same connector (Port A) for connection to the Support Tool and connection to the Host. If this connector is currently connected to the host, disconnect the cable from it and connect it to the Support Tool (personal computer) before attempting screen data transmission.
Select “Maintenance Mode”.
[ SYSTEM MENU ]
Quit
Transmit Mode
Maintenance Mode
[ MAINTENANCE MENU ]
Quit DIP-SW Status
PT Setting
I/O Check
Init. Memory
Memory Switch
Select “I/O Check”.
116
System Maintenance
Section 3-9
[ I/O CHECK MENU ]
Quit LCD Display
Comm. Check LED Check
Buzzer
Touch Switch
Data Memory
Select “Comm. Check”.
Select “Tool I/F”.
[ COMM. CHECK MENU ]
Quit
Tool I/F
[ TOOL I/F INPUT CHECK ]
The data received from the connected Support Tool are displayed in hexadecimal numbers.
Checking the
Communications with the
Host (NT20-ST128)
EXIT
When the check is finished, press the Exit touch switch. The NT20 will enter the I/O CHECK MENU.
Execute a NT20-to-Host communications check by the menu operation from the System Menu as described below.
Select “Maintenance Mode”.
[ SYSTEM MENU ]
Quit
Transmit Mode
Maintenance Mode
117
System Maintenance
Section 3-9
[ MAINTENANCE MENU ]
Quit DIP-SW Status
PT Setting
I/O Check
Init. Memory
Memory Switch
Select “I/O Check”.
[ I/O CHECK MENU ]
Quit LCD Display
Comm. Check LED Check
Buzzer
Touch Switch
Data Memory
Select “Comm.Check.
[ COMM. CHECK MENU ]
Quit
Tool I/F
RS-232C I/F
[ RS-232C I/F INPUT MENU ]
Checking the LCD
118
Exit
When the check is finished, press the EXIT touch switch. The NT20 will enter the RUN mode.
Check the NT20 LCD by using the menu operation from the System Menu as described below.
System Maintenance
[ SYSTEM MENU ]
Quit
Transmit Mode
Maintenance Mode
Section 3-9
Select “Maintenance Mode”.
Checking the Buzzer
[ MAINTENANCE MENU ]
Quit DIP-SW Status
PT Setting
I/O Check
Init. Memory
Memory Switch
Select “I/O Check”.
[ I/O CHECK MENU ]
Quit LCD Display
LED Check Comm. Check
Buzzer
Touch Switch
Data Memory
Select “LCD Display”.
Select “RS-232C I/F”.
• The LCD displays dots (segments of the screen) line by line beginning with the top left corner. If all the dots are displayed normally, the NT20 will enter the I/O CHECK MENU after all the dots have been turned off.
• To cancel the LCD indication check, press any touch switch (anywhere) on the screen. The I/O Check Menu will be redisplayed.
Check the NT20 buzzer by using the menu operation from the System Menu as described below.
Select “Maintenance Mode”.
[ SYSTEM MENU ]
Quit
Transmit Mode
Maintenance Mode
119
System Maintenance
Section 3-9
[ MAINTENANCE MENU ]
Quit DIP-SW Status
PT Setting
I/O Check
Init. Memory
Memory Switch
Select “I/O Check”.
Checking the LED
Note
Select “Buzzer”.
[ I/O CHECK MENU ]
Quit LCD Display
Comm. Check LED Check
Buzzer
Touch Switch
Data Memory
• If the buzzer function is normal, the continuous buzzer sound will be made.
• To stop the buzzer, press “EXIT” touch switch in the buzzer check screen.
The NT20 will enter the I/O CHECK MENU.
Though memory switch setting for the buzzer has been made for OFF, the buzzer will sound when the buzzer check is executed.
Check the LED by using the menu operation from the System Menu as described below.
Select “Maintenance Mode”.
[ SYSTEM MENU ]
Quit
Transmit Mode
Maintenance Mode
[ MAINTENANCE MENU ]
Quit DIP-SW Status
PT Setting
I/O Check
Init. Memory
Memory Switch
Select “I/O Check”.
120
System Maintenance
Section 3-9
[ I/O CHECK MENU ]
Quit LCD Display
Comm. Check LED Check
Buzzer
Touch Switch
Data Memory
Select “LED Check”.
The “RUN” LED on the front face of the NT20 will flash. Flashing cycle is about
1 s (500 ms ON and 500 ms OFF).
• To quit the LED check, press the “EXIT” touch switch. The NT20 will enter the I/O CHECK MENU.
Checking the Screen Memory
Check the screen memory by using the menu operation from the System
Menu as described below.
Note
When the screen data memory is checked, the memory is initialized and all the screen data is lost. Check that the screen data has been backed up using the Support Tool before executing a screen data memory check.
Select “Maintenance Mode”.
[ SYSTEM MENU ]
Quit
Transmit Mode
Maintenance Mode
[ MAINTENANCE MENU ]
Quit DIP-SW Status
PT Setting
I/O Check
Init. Memory
Memory Switch
Select “I/O Check”.
121
System Maintenance
[ I/O CHECK MENU ]
Quit LCD Display
Comm. Check LED Check
Buzzer
Touch Switch
Data Memory
Section 3-9
Select “Data Memory”.
[ SCREEN DATA MEMORY CHECK ]
Caution!!
This test will destroy
the Screen Data.
Press “TEST START”.
Pressing “Cancel” will cancel the memory check.
TEST
START
CANCEL
The screen memory check will start.
While the screen memory is checked, the “Memory checking...” message will be displayed.
• If the memory check has been normally completed, the “Memory is OK” message will be displayed.
• To quit the memory check, press the “Cancel” touch switch. The NT20 will enter the I/O CHECK MENU.
• If the “Memory error!” message is displayed, the screen data memory may have been used up to its service life or there may be a hardware fault. In that case, initialize the screen data memory and check the memory again. If the same error message is displayed again, consult the
OMRON Service Center.
3-9-2 Checking the PT Setting
Display the NT20 settings by using the menu operation from the System Menu as described below.
[ SYSTEM MENU ]
Quit
Transmit Mode
Maintenance Mode
Select “Maintenance Mode”.
122
System Maintenance
Section 3-9
[ MAINTENANCE MENU ]
Quit DIP-SW Status
PT Setting
I/O Check
Init. Memory
Memory Switch
Select “PT Setting”.
(Host link)
[ PT SETTING ]
PT Control Area DM0000
PT Notify Area DM0010
Comm. Type
Baud Rate
Host Link
9600bps
EXIT
(NT Link (1:N))
(NT Link (1:1))
[ PT SETTING ]
PT Control Area DM0000
PT Notify Area DM0010
Comm. Type NT Link
EXIT
[ PT SETTING ]
PT Control Area
PT Notify Area
Comm. Type
Unit No.
EXIT
(C200H)
DM0000
DM0010
NT Link 1:N
7
(RS-232C) (NT20-ST128)
[ PT SETTING ]
PT Control Area DM0000
PT Notify Area DM0010
Comm. Type C200H
Unit No. 0
EXIT
[ PT SETTING ]
Data Bits
Stop Bits
Parity Check
Flow Control
Baud Rate
EXIT
8 bits
1 bit
Even
RS/CS
19200 bps
• The current PT settings will be displayed.
• Pressing the “EXIT” touch switch will exit the PT settings display, and the
NT20 will return to the RUN Mode.
123
System Maintenance
Section 3-9
3-9-3 Checking the NT20 DIP Switch Settings
Display the NT20 DIP switch settings by using the menu operation from the
System Menu as described below.
[ SYSTEM MENU ]
Quit
Transmit Mode
Maintenance Mode
Select “Maintenance Mode”.
[ MAINTENANCE MENU ]
Quit DIP-SW Status
PT Setting
I/O Check
Init. Memory
Memory Switch
Select “DIP-SW Status”.
[ DIP-SWITCH STATUS ]
1. Forced Init. No
2. Lanugage Select Enable
3. Mode Change Enable
(1/2)
Page
[SW2]
1
2 3 4
5
6
ON
OFF
EXIT
[ DIP-SWITCH STATUS ]
4. Reserved
5. Resouce Init.
6. System Init.
OFF
Disable
Disable
(2/2)
Page
[SW2]
1 2
3 4
5
6
ON
OFF
EXIT
• The NT20 DIP switch status is displayed.
• Pressing the EXIT touch switch clears the DIP switch status display from the screen and causes the NT20 to enter the RUN mode.
124
System Maintenance
Note
Section 3-9
If the DIP switch settings have been changed when the NT20 is powered, reset the power to the NT20. The changes with the DIP switches become effective only after the power supply is reset.
125