Transferring the Resource Data
Section 3-11
3-11 Transferring the Resource Data
The resource data of the NT20 can be changed using the System Transfer
Tool.
The System Transfer Tool is automatically installed in the personal computer when the NT20 Support Tool is installed.
For details on how to start up the System Transfer Tool, and the System
Transfer Tool operation, refer to the NT-series Support Tool Operation Manual
(V061-E1@).
Transferring the Resource
Data from the System
Transfer Tool
Operation
Note
An NT20 which has no resource data registered in it will display a resource error screen.
For details on System Transfer Tool operations, refer to the NT-series Support
Tool Operation Manual (V061-E1@).
In order to transfer the resource data from the System Transfer Tool, first connect the NT20 to a personal computer running the System Transfer Tool using the appropriate cable, then proceed as follows.
Reference
The NT20 uses the same connector (Port A) for connection to the Support
Tool and connection to the host. If this connector is currently connected to the host, disconnect the cable from the host and connect it to the Support Tool
(personal computer) before attempting to transfer the resource data.
1.
Connect the NT20 to the personal computer running the System Transfer
Tool, then turn ON the power to the NT20.
2.
Turn ON the power to the personal computer and start up the System
Transfer Tool.
3.
When the power to the NT20 is turned ON, the screen shown below will be displayed.
[ Resource Transmit ]
Erase resource
Download resource
4.
Press the Download resource Button to enter the resource transfer mode, as shown below.
[ Download Resource ]
ABORT
5.
The NT20 is now on standby for reception. Start transfer of the program using the System Transfer Tool.
129
Transferring the Resource Data
Section 3-11
When the NT20 starts reception, the screen shown below will be displayed.
[ Download Resource ]
Downloading
0KB
ABORT
6.
When transfer of the system program has completed, the NT20 will be displays the screen shown below.
Downloading is completed.
Turn OFF the DIP Switch 2-5
And push the Reset Switch.
Then return to RUN mode.
Points to Observe during
Transfer of the Resource
Data
Method for Erasing the
Resource Data
Operation
If any of the following events or a system error occurs during transfer of the resource data, the program will not be installed in the NT20 correctly.
• The power to the NT20 is turned OFF or the NT20 is reset during transfer.
• The power to the personal computer that is running the System Transfer
Tool is turned OFF or the personal computer is reset during transfer.
• The cable connecting the personal computer running the System Transfer
Tool and the NT20 becomes disconnected or sustains a wire breakage during transfer.
• Transfer is terminated by pressing the ABORT Button on the NT20.
• Transfer is terminated by pressing the ESC key of the personal computer running the System Transfer Tool.
In the event of any of the above, a resource error will occur.
To prevent this, turn ON DIP switch SW2-5 to erase the resource data after the problem has occurred. For details on erasing the resource data with the
DIP switch, refer to Method for Erasing the Resource Data.
In order to erase the resource data, the resource data area must be cleared. If resource data already exists, it must be erased before the new data can be transferred.
Use the following procedure to erase the resource data.
1.
Set DIP SW2-5 to the ON position and turn ON the power or reset. The following screen will be displayed.
130
Transferring the Resource Data
[ Resource Transmit ]
Erase resource
Download resource
Section 3-11
2.
If you do want to erase the resource data, press the Erase resource Button. The following screen will be displayed.
Erase resource?
Yes
No
3.
Press the No Button if you want to quit without erasing the resource data.
If you do want to erase the resource data, press the Yes Button. This will start erasure of the resource data.
During erasure, the screen shown below is displayed:
Erase resource?
Yes
Erasing
No
4.
On completion of erasure, the screen shown below will be displayed.
[ Resource Transmit ]
Erase resource
Download resource
131
Transferring the Resource Data
Section 3-11
132
SECTION 4
NT20 Functions and Operation
This section describes the functions of the NT20.
4-1 Screen Creation Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-2 Outline of Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-2-1 NT20 Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-2-2 Characters and Figures Which Can Be Displayed . . . . . . . . . . . . . .
4-2-3 Communications with the Host . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-3 Screen Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-3-1 Classification of Screens. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-3-2 Screen Attributes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-4 Memory Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-4-1 Character-String Memory Table . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-4-2 Numeral Memory Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-5 Bar Graphs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-5-1 Bar Graph Functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-6 Lamps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-6-1 Lamp Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-7 Touch Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-7-1 Functions of Touch Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-7-2 Screen Switching Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-7-3 System Key Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-8 Numeral Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-8-1 The Numeral Setting Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-8-2 Types of Numeral Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-8-3 Creating Numeric Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-8-4 Using Numeric Keys. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-8-5 Using The Thumbwheel Type of Numeral Setting. . . . . . . . . . . . . .
4-8-6 Settings for Numeral Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
156
156
157
158
152
153
154
154
160
161
162
147
147
150
150
142
144
144
145
134
136
136
137
138
140
140
133