7-3 Maintenance of the NT20. Omron NT 20S-ST122-V1, NT 600M-LB122-V1, NT 20M-DT121-V2, NT 20-ST128, NT 20, NT 20M, NT 20S-ST121-EV3, NT 20-ST121-E, NT 20S
বিজ্ঞাপন
বিজ্ঞাপন
Maintenance of the NT20
Section 7-3
7-3 Maintenance of the NT20
Carry out maintenance work in order to ensure that the NT20 is always used in its optimum condition.
Spare PT
Backlight
!WARNING
Do not attempt to take the PLC apart and do not touch any internal parts while the power is being supplied. Doing either of these may result in electrical shock.
It is advisable to have a spare NT20 available to minimize system downtime in the event of an NT20 failure or if the screen display becomes difficult to read due to deterioration of the display unit.
The backlight must be replaced when the brightness of the display backlight dims and the display becomes difficult to see. The backlight cannot be replaced by the user.
Contact your nearest OMRON representative.
7-4 Inspection and Cleaning
Clean and inspect the NT20 regularly to ensure that it is always used in its optimum condition.
Cleaning Method
Inspection Method
Note
If the display is dirty the screen is difficult to see. Clean the screen from time to time as follows.
• In daily cleaning, wipe the display with a soft dry cloth.
• If the soiling cannot be removed with a dry cloth, wet the cloth with water, wring it out well and wipe the display with it.
• If rubber or vinyl products, tape, etc. are left stuck to the display for long periods they will cause staining. If such items are stuck to the display, remove them during cleaning.
Never use volatile solvents such as benzene or thinners, or dusters.
In normal environments, inspect the NT20 at intervals of between 6 months and a year. In environments that are extremely hot and humid, or very dusty environments, shorten the inspection interval.
• Items Required for Inspection
Prepare the following items before starting the inspection.
• The tools supplied with the NT20
• Screwdrivers (Phillips, flat-head)
• Tester (or digital voltmeter)
• Industrial alcohol
• 100% cotton cloth
• Hygrometer (required in some cases)
• Thermometer (required in some cases)
• Synchroscope (required in some cases)
• Pen-writing oscilloscope (required in some cases)
253
Inspection and Cleaning
Section 7-4
• Faulty Display Pixels
Although the LCD panel has been manufactured with extremely high-level technology, there can sometimes be pixels that will not light or that will be lit constantly. These are characteristic of LCD panels and are not an indication of a faulty display. Please understand that, although we are constantly striving to keep these pixels to a minimum, it is not possible with present technology to eliminate them completely.
• Points Inspected
Inspect the following points to determine if there is any divergence from the stated criteria. If there is, either improve the surrounding environment so that the values fall within the stated range, or adjust the NT20.
Point Inspected Inspection Details
Power supply voltage Fluctuation in power supply terminal voltage
Criterion
Permissible voltage fluctuation range (24 VDC
−
15% +15%)
0 to 50
°C
Inspection Instrument
Tester
Ambient environmental conditions
Ambient temperature (temperature in the operation panel)
Thermometer
Ambient humidity
(humidity in the operation panel)
Presence/absence of dust
35% to 85% Hygrometer
Mounting conditions Looseness of mounting brackets etc.
Looseness of screws in external wiring
Conditions of external connecting cables
Dust must not be settled Visual inspection
To be no looseness
Connector connections of connecting cable To be fully inserted and locked, with no looseness
To be no looseness
Faults such as incipient disconnections.
Accessory tools
Phillips screwdriver
Visual inspection
External appearance Peeling of front sheet Front sheet must not show any signs of peeling.
Visual inspection
Note
(1) Do not attempt to disassemble the NT20 for repair or modification.
(2) The disposal of the NT20 may be regulated by national or local authorities. Dispose of them according to the laws and regulations of the relevant country and local authority.
(3) When replacing the NT20 after discovering a fault during inspections, note the following points:
• Be sure to switch the power OFF before replacement.
• After replacement, check that the new NT20 is not subject to the same error.
• If a faulty unit is returned for repairs, write as detailed a description of the fault as possible and send this description together with the unit to the OMRON address indicated on the back cover of this book.
254
ডাউনলোড
বিজ্ঞাপন