Host Connections by RS-232C (NT20-ST128)
Section 2-8
2-8 Host Connections by RS-232C (NT20-ST128)
Connect the NT20-ST128 with an RS-232C Interface Unit installed to the host computer with an RS-232C cable.
An RS-232C connection allows a single NT20 to be connected to the host.
A computer or other control device with a built-in RS-232C interface is a suitable host for connection to the NT20.
2-8-1 Host Computer Communications Settings
Set the host communications conditions according to the following table.
Item
Baud rate
Data bits
Stop bits
Parity Even, Odd, None
Flow control RS/CS control
XON/XOFF control
None
Setting
Set to the same baud rate as the NT20: 2400, 4800, 9600, 19200
7 bits/8 bits
1 bit/2 bits
Note
Set the same communications conditions at the NT20 and Host.
Refer to the appropriate instruction manuals for the method of setting the Host communications conditions.
Set to the maximum baud rate supported by both the NT20 and Host.
The communications condition settings of the NT20-ST128 are set with the
RS-232C communications conditions memory switches.
2-8-2 Connector Pin Arrangement
The RS-232C connection between the NT20 and Host is described below.
NT20 Interface Unit
The connector specifications are described below.
Electrical characteristics: Conforms to EIA RS-232C specifications.
Signal direction: Signal input and output are relative to the host computer.
1 6
5 9
Connector pin #
4
5
2
3
Signal name
Send data
Receive data
Request to send
Clear to send
Abbreviation
SD (TXD)
RD (RXD)
RS (RTS)
CS (CTS)
→
←
→
←
Signal direction
NT20
← → Host
79
Host Connections by RS-232C (NT20-ST128)
Section 2-8
Connecting to the Host
Computer
Note
Connector pin #
6
9
Signal name
+5 V output, 150 mA max.
Signal ground
Abbreviation
+5 V
SG (GND)
→
Signal direction
NT20
← → Host
---
Note
Unlisted pins are not used.
For cable parts and the wiring method, refer to Appendix C Transporting and
Storing PTs on page 263.
Use a cable that is compatible with the RS-232C connector of the host to connect the NT20 and the host (see the example in the figure below).
In the example shown here, the cable connects the 9-pin connector of the
NT20 and 25-pin connector of the host. If the host has a 9-pin RS-232C connector, use an RS-232C cable with 9-pin connectors at both ends.
NT20
9-pin connector
Host Interface connector
(RS-232C, 9-pin type)
RS-232C cable
25-pin connector
!Caution When making the connection, turn OFF the power to the NT20 and PLC before disconnecting or connecting any connector.
!Caution After connecting the communications cable, always secure it with the screws.
Otherwise the cable may disconnect, causing operation to fail.
Note
If using the +5 V supply of pin No.6, check first that the equipment that is to receive the supply has a current capacity no greater than 150 mA. The +5 V output of the NT20 is +5 V DC
±5%, 150 mA max.
Do not use both port’s +5 V output at the same time.
80
SECTION 3
System Menu Operation
This section describes the operation of the System Menu focusing on the procedure to start up the NT20. Functions which will be convenient to use the NT20 and those which are useful for the system maintenance are also explained here.
3-1 Operation Flow by the System Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-2 Starting the NT20 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-2-1 Changing the System Settings or Screen Data . . . . . . . . . . . . . . . . .
3-3 Operation Modes and the System Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-3-1 System Menu and the Operation Modes. . . . . . . . . . . . . . . . . . . . . .
3-3-2 Menu Tree. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-3-3 Operations with the System Menu . . . . . . . . . . . . . . . . . . . . . . . . . .
3-4 Initializing Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-4-1 Initialization by Using the System Menu . . . . . . . . . . . . . . . . . . . . .
3-4-2 Initialization by Using the DIP Switch (Forced Initialization). . . . .
3-5
Setting the Conditions of Communications with the Host by Using the Memory Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-5-1 Selecting the Host Communications Method . . . . . . . . . . . . . . . . . .
3-5-2 Selecting the Host Communications Port . . . . . . . . . . . . . . . . . . . . .
3-5-3 Selecting the Host Link Communications Speed . . . . . . . . . . . . . . .
3-5-4 Selecting the NT Link (1:N) Communications Speed . . . . . . . . . . .
3-5-5 Selecting Unit Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-5-6 Selecting the Automatic Reset Function. . . . . . . . . . . . . . . . . . . . . .
3-5-7 Setting RS–232C Communications Conditions (NT20-ST128). . . .
3-6 Registering the Screen Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-7 Starting the Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-8 Various System Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-8-1 Setting the Key Press Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-8-2 Using the Buzzer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-8-3 Backlight OFF Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-8-4 Language Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-8-5 Support Tool Mode Setting (NT20-ST121-E) . . . . . . . . . . . . . . . . .
3-8-6 Lamp Bit Control (NT20-ST128). . . . . . . . . . . . . . . . . . . . . . . . . . .
3-9 System Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-9-1 I/O Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-9-2 Checking the PT Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-9-3 Checking the NT20 DIP Switch Settings . . . . . . . . . . . . . . . . . . . . .
3-10 Transferring the System Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-11 Transferring the Resource Data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
106
107
109
110
99
102
105
106
95
96
97
98
91
93
94
122
124
126
129
111
112
115
115
84
84
84
86
82
83
83
88
88
90
81